manualshive.com logo in svg

Dixon RZL-400, Руководство по эксплуатации и техническому обслуживанию, Страница: 3 / 78

Поделиться
Скачать
Dixon RZL-400 Скачать руководство пользователя страница 3

3

Rotary Lobe Pumps - RZL-400 Series

800.789.1718

DO’S & DON’TS

DO

 read and understand these instructions before installing or using the pump.

DO

 use Dixon spare parts when replacing a component of the pump.

DO NOT

 service the pump while it is running.

DO NOT

 place the pump in an application where the service ratings are exceeded.

DO NOT

 modify the pump. Modifying the pump creates unsafe conditions and voids all warranties.

SAFETY PRECAUTIONS WHEN INSTALLING PUMP

DO

 use an authorized electrician when connecting the pump.

DO

 observe the mechanical limits of the pump (refer to the pump performance sheet).

DO

 install a throttling valve in the discharge line.

DO NOT

 install a throttling valve in the suction line.

SAFETY PRECAUTIONS WHEN OPERATING PUMP

DO

 allow only qualified personnel to operate this pump.

DO NOT

 start the pump until all personnel are clear.

DO NOT

 touch the pump or the lines when pumping hot fluids or when performing Clean In Place (CIP) procedures.

DO NOT

 run the pump with BOTH the suction inlet and discharge outlet blocked. Running the pump with the inlet 

blocked will cause serious damage to the pump.

DO NOT

 check pump rotation with liquid in the pump.

DO NOT

 run the pump with the front cover removed. The rotors and rotor case could be damaged or may cause severe 

injury.

DO NOT

 operate the pump with the safety guard removed.

SAFETY PRECAUTIONS WHEN SERVICING PUMP

DO

 ensure the pump is cool to touch before performing service.

DO

 relieve all pressure and drain all fluids from pump and connected piping before performing service.

DO

 ENSURE POWER TO THE UNIT HAS BEEN DISCONNECTED PRIOR TO PERFORMING ANY PUMP 

MAINTENANCE OR CLEANING.

DO

 exercise caution and wear protective clothing when using lye or acid for cleaning.

Safety Information

Содержание RZL-400















































































Отзывы:

Нет отзывов