background image

5.3 Routine Maintenance Schedule

    • The filter frame must be replaced 
        so  that  the  cage  side  is  facing 
        upwards  to  prevent  the  media   
        from being sucked out of the frame 

• Inspect the HEPA after filters 
   and replace if the filters are  
   saturated

3.  Clean the inside of the unit completely from top to  bottom, using 
     wire brush or scraper and a pressure washer to remove all 
     accumulated sludge and debris

    • Remove the inlet duct to clean the inside of the back of the 
       collector  and inspect the inlet ductwork for dust accumulation

4.  Drain the dirty water using the optional WV-55 sludge-vacuum to 
     separate the metal fines from the water, remove sludge on the 
     bottom of the tank and skim the residual material floating on the 
     water surface

5.  Open the water level control box to inspect  
     the level probes or ultrasonic sensor and 
     remove all accumulated particulate

1. Open the knobs or latches on the two 
     front panels of the wet dust collector

2.  Inspect the mist eliminator filters inside the unit for holes or dust 
     accumulation, replace the media if torn or dirty

•  

All debris must be 

    stored in a ventilated   
    metal drum to prevent 
    hydrogen gas buildup

•  If the collector has the 
    optional strainer system, 
    remove the basket and 
    dump the accumulated 
    dust, clean out the
    basket and replace it. 

•  Dust needs to be 
    disposed of according 
    to local regulation

6.  If the level probe is loose, tighten the 
     terminal screw and ensure the probes are at 
     the right level and touching each other. 
     Ensure the probe gasket is cleaned of all 
     residue

•  If the level probes require maintenance 
    use an abrasive sponge to remove all 
    accumulated particulate

7.  Ensure the passage from the probe housing 
     to the water basin is free and clear of 
     debris

8.  Once the entire machine has been cleaned 
     out, re-install the front doors, mist filters,  
     and probe box assembly

13

Whenever several inches of dust buildup inside the wet collector water tank, it is necessary to remove the material as soon as possible. Depending on 
application dust loading, The Wet Collector may needs to be maintained daily.

Cleaning Instructions:

Содержание TYPHOON WX Series





















Отзывы: