Ditch Witch ST37x Скачать руководство пользователя

Страница: 41 / 112

Prepare - 40

ST37x Operator’s Manual

Classify Jobsite

Select a Classification

Jobsites are classified according to underground hazards present.

Jobsite hazards could cause death or serious injury. Use

correct equipment and work methods. Use and maintain proper safety
equipment.

To help avoid injury:

•

Wear personal protective equipment including hard hat, safety eye wear, and hearing protection.

•

Do not wear jewelry or loose clothing.

•

Comply with all utility notification regulations before digging or drilling.

•

Mark proposed path or excavation area with white paint and have underground utilities located
before working.

•

Verify location of previously marked underground hazards.

•

Mark jobsite clearly and keep spectators away.

Remember, jobsite is classified by hazards in place -- not by line being installed.

If working . . .

then classify jobsite as . . .

within 10’ (3 m) of a buried electric line

electric

within 10’ (3 m) of a natural gas line

natural gas

in sand or granite which is capable of producing crystalline silica
(quartz) dust

crystalline silica (quartz) dust

within 10’ (3 m) of any other hazard

other

NOTICE:

If you have any doubt about jobsite classification, or if jobsite might contain unmarked

hazards, take steps outlined previously to identify hazards and classify jobsite before working.

Содержание ST37x

















































































































Результаты поиска

Содержание ST37x

Отзывы:

Похожие инструкции для ST37x

Бренды по названию

Популярные бренды

Ditch Witch ST37x, Руководство оператора

Результаты поиска

Содержание ST37x

Отзывы:

Похожие инструкции для ST37x

Бренды по названию

Популярные бренды