Ditch Witch ST37x Скачать руководство пользователя

Страница: 26 / 112

ST37x Operator’s Manual

Controls - 25

Graphic Display

Engine coolant
temperature indicator

Displays coolant temperature.

IMPORTANT:

If temperature goes

above 230°F (110°C):

1. Stop operation, set throttle to low
idle, and allow engine to cool.

2. Stop engine.

3. Check coolant level.

4. Ensure radiator is clean.

DPF regen inhibited
indicator

Lights when automatic
exhaust cleaning (DPF
regeneration) has been
inhibited.

IMPORTANT:

System will remain in

inhibited mode until unit is returned to
automatic mode. Manual exhaust
cleaning (DPF REGEN) must be
initiated through Tier 4 menu when
this indicator is on. See “Exhaust
Cleaning - Tier 4 Only” on page 70.

10. Hourmeter

Displays engine operating
time.

Use these times to schedule service.

11. Engine speed increase

button

To increase engine speed,
push once.

To increase to full speed,
push twice.

IMPORTANT:

•

Increasing engine speed also
increases attachment speed.

•

Each button press increases
engine by 360 rpm.

Item

Description

Notes

c00ic116w.eps

c00ic105w.eps

c00ic106w.eps

HRS

c00ic107w.eps

Содержание ST37x

















































































































Результаты поиска

Содержание ST37x

Отзывы:

Похожие инструкции для ST37x

Бренды по названию

Популярные бренды

Ditch Witch ST37x, Руководство оператора

Результаты поиска

Содержание ST37x

Отзывы:

Похожие инструкции для ST37x

Бренды по названию

Популярные бренды