Ditch Witch ST37x Скачать руководство пользователя

Страница: 35 / 112

Controls - 34

ST37x Operator’s Manual

Controls

Boom lift control

To lower boom, push.

To raise boom, pull.

Attachment drive
control

To engage attachment drive
in reverse, push forward.

To engage attachment drive
in forward, pull back.

IMPORTANT:

Use foot pedal to hold

attachment control in the on position
when hands are busy operating track
drive controls.

Attachment drive foot
control

To hold attachment drive in
engaged position (forward or
reverse), move lever in
desired direction, and press
pedal.

To return attachment drive
control to neutral, release
pedal.

IMPORTANT:

•

Use foot pedal to hold attachment
control in the on position when
hands are busy operating track
drive controls.

•

If attachment drive control handle
moves when foot control pedal is
pressed completely, adjust pedal.

See “Adjust Attachment Drive
Controls” on page 89.

Item

Description

Notes

c00ic083a.eps

Содержание ST37x

















































































































Результаты поиска

Содержание ST37x

Отзывы:

Похожие инструкции для ST37x

Бренды по названию

Популярные бренды

Ditch Witch ST37x, Руководство оператора

Результаты поиска

Содержание ST37x

Отзывы:

Похожие инструкции для ST37x

Бренды по названию

Популярные бренды