Ditch Witch ST37x Скачать руководство пользователя | Manualshive

Страница: 13 / 112

background image

Safety - 12

ST37x Operator’s Manual

Emergency Procedures

If an Electric Line is Damaged

If you suspect an electric line has been damaged and you are on tractor, DO NOT MOVE. Remain on
tractor and take the following actions. The order and degree of action will depend upon the situation.

•

Warn people nearby that an electric strike has occurred. Instruct them to leave the area and contact
utility.

•

Raise attachments and drive from immediate area.

•

Contact utility company to shut off power.

•

Do not return to jobsite or allow anyone into area until given permission by utility company.

If you suspect an electric line has been damaged and you are

off tractor

, DO NOT TOUCH TRACTOR.

Take the following actions. The order and degree of action will depend upon the situation.

•

LEAVE AREA. The ground surface may be electrified, so take small steps with feet close together to
reduce the hazard of being shocked from one foot to the other. For more information, contact your

Ditch Witch

®

dealer.

•

Contact utility company to shut off power.

•

Do not return to jobsite or allow anyone into area until given permission by utility company.

«
...
11
12
13
14
15
...
»

Содержание ST37x

















































































































Отзывы:

Нет отзывов

Похожие инструкции для ST37x

Бренд: GALLERY Страницы: 18

Бренд: FENDT Страницы: 31

Бренд: JB Systems Страницы: 12

Бренд: Abicor Binzel Страницы: 92

Бренд: Dana Design Страницы: 20

Бренд: Haki Страницы: 24

Бренд: Dakota Digital Страницы: 5

Бренд: Federal Signal Corporation Страницы: 4

Бренд: ParaBody Страницы: 7

Бренд: Patty-O-Matic Страницы: 28

Бренд: Keller Страницы: 12

Бренд: MacDon Страницы: 49

Бренд: MacDon Страницы: 49

Бренд: MacDon Страницы: 4

Бренд: Qazqa Страницы: 4

Бренд: Qlightec Страницы: 12

Бренд: TECshow Страницы: 22

Бренд: Lightolier Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды