Ditch Witch SK500 Скачать руководство пользователя

Страница: 21 / 75

Controls - 20

SK500 Operator’s Manual

CMW

11. Right track drive

control

To move forward, push.

To move backward, pull.

To go faster in either
direction, move control farther
from neutral.

To stop, move to neutral.

To turn right, move left control forward
and right control back.

To turn left, move right control forward
and left control back.

To counter-rotate in either direction,
move controls fully to ends in the
directions indicated above.

12. Left track drive control

To move forward, push.

To move backward, pull.

To go faster in either
direction, move control farther
from neutral position.

To stop, move to neutral
position.

To turn right, move left control forward
and right control back.

To turn left, move right control forward
and left control back.

To counter-rotate in either direction,
move controls fully to ends in the
directions indicated above.

Item

Description

Notes

Содержание SK500












































































Результаты поиска

Содержание SK500

Отзывы:

Похожие инструкции для SK500

Бренды по названию

Популярные бренды

Ditch Witch SK500, Руководство оператора

Результаты поиска

Содержание SK500

Отзывы:

Похожие инструкции для SK500

Бренды по названию

Популярные бренды