Ditch Witch SK500 Скачать руководство пользователя

Страница: 14 / 75

SK500 Operator’s Manual

Safety - 13

Safety Alerts

CMW

Explosion possible. Serious injury or equipment damage could occur.

Follow directions carefully.

Incorrect procedures could result in death, injury, or property damage.

Learn to use equipment correctly.

Improper control function could cause death or serious injury. If control does

not work as described in instructions, stop machine and have it serviced.

Looking into fiber optic cable could result in permanent vision damage. Do

not look into ends of fiber optic or unidentified cable.

Fluid or air pressure could pierce skin and cause injury or

death. Stay away.

Runaway possible. Machine could run over you or others. Learn how to use

all controls. Start and operate only from operator’s position.

Fire or explosion possible. Fumes could ignite and cause burns. No

smoking, no flame, no spark.

Содержание SK500












































































Результаты поиска

Содержание SK500

Отзывы:

Похожие инструкции для SK500

Бренды по названию

Популярные бренды

Ditch Witch SK500, Руководство оператора

Результаты поиска

Содержание SK500

Отзывы:

Похожие инструкции для SK500

Бренды по названию

Популярные бренды