Distech Controls EC-BOS-6AX Скачать руководство пользователя страница 22

Страница: 22 / 28

EC-BOS-6

Mounting and Wiring Instructions

Revised: February 2008

Part Number: 05DI-HIBS6AX-10

Replacing the base assembly

Standard Replacement Parts

Standard Replacement Parts

Standard replacement parts are listed in

Table 4

and can be ordered from stock without restriction. Standard

replacement parts cannot be returned for credit and should be disposed of in an appropriate manner.

Note

Screws used for the EC-BOS-6

are standard #6-32

3/8" types, which you can obtain locally if lost.

New Replacement Units

To replace a faulty unit, order and install a

new

EC-BOS-6

—please note that EC-BOS

series products do

not

have special “field replacement units,” or FRUs, with separate part numbers.

If the faulty EC-BOS-6

still in warranty

, you can receive credit by returning it to Distech Controls. Be sure

to contact Distech Controls for a return authorization (RMA) number before shipping an item for return credit.
See

“Federal Communications Commission (FCC),”

page 24, for more details.

Note

Before ordering a new EC-BOS-6

, it is strongly recommended that you contact your normal technical

support resource to eliminate the possibility of a software issue or mis-configuration problem.

Replacing the base assembly

Caution

Before handling circuit boards, discharge any accumulated static by touching the metal surface of
the EC-BOS-6

. For details, see the

“Static Discharge Precautions”

section on page 4.

To replace the EC-BOS-6

base assembly in the field, proceed as follows:

Procedure 6

Replacing a EC-BOS-6

base assembly.

Step 1

Using the appropriate Niagara

software tool, back up the EC-BOS

’s configuration to your PC.

Step 2

Remove power to the EC-BOS-6

. The unit should power down automatically.

Note

If I/O accessory modules are installed and any I/O points have voltage, turn the devices off or
disconnect power to them.

Step 3

Note positions of all communications and other wiring cables going to the EC-BOS-6

, as well as all

installed accessory modules (if they must be removed). If necessary, label connectors and accessory
modules to avoid mis-connection later, after EC-BOS-6

is replaced.

Table 4

Standard replacement parts.

Part Number

Description

10499

NiMH Battery Pack (with battery bracket)—see

“Replacing the Battery,”

page 20

10027

RS-485 connector plug, 3-position

Содержание EC-BOS-6AX





























Результаты поиска

Содержание EC-BOS-6AX

Отзывы:

Похожие инструкции для EC-BOS-6AX

Бренды по названию

Популярные бренды

Distech Controls EC-BOS-6AX, Монтаж и подключение

Результаты поиска

Содержание EC-BOS-6AX

Отзывы:

Похожие инструкции для EC-BOS-6AX

Бренды по названию

Популярные бренды