Distech Controls EC-BOS-6AX Скачать руководство пользователя страница 15

Страница: 15 / 28

Wiring Details

Communications Wiring

EC-BOS-6

Mounting and Wiring Instructions

Part Number: 05DI-HIBS6AX-10

Revised: February 2008

Note

Prior to connecting cables, provide strain relief for them to prevent damage to the controller.

Figure 5

EC-BOS-6

bottom side (cover removed).

Ethernet

Two, female 10/100-Mbit Ethernet connections are provided on the EC-BOS-6

. These are RJ-45 connectors

labeled LAN2 and LAN1. Use a standard Ethernet patch cable for connecting to a hub or Ethernet switch. An
activity LED for each Ethernet port is visible, and are labeled “LAN2” and “LAN1” on the cover.

The factory-default IP address for LAN1 on an EC-BOS-6

192.168.1.12n

, where the last numeral

in the

address matches the EC-BOS-6

’s serial number, and subnet mask is

255.255.255.0

. By default, LAN2 on an

EC-BOS-6

is disabled. Refer to the

EC-BOS

Install and Startup Guide

for details on changing IP address.

Note

Typically, you

only use LAN1

(primary port), unless you have a specific application for isolating a

driver’s network traffic to a separate LAN, using LAN2. Do

not

use LAN2 as the primary port.

Serial

There are two serial ports on the EC-BOS-6

base unit. Each has a UART capable of operation up to 115,200

baud. At the bottom of the board (see

Figure 5

), the left port is an

RS-232

port using an DB-9 plug (male)

connector. To the right of this is a two-wire with shield, isolated

RS-485

port, using a screw-terminal connector

plug.

Note

A green “receive” LED and yellow “transmit” LED are provided for each serial port. These LEDs are
located on the bottom board, on the

opposite side

of the serial connectors (see

Figure 2

on page 7).

These LEDs are labeled on the board (COM1, COM2) and are not visible with the cover on.

RS-232—

An RS-232 serial port using a male DB-9 connector always operates as COM1. You can use standard

DB-9 serial cables with this port. The EC-BOS-6

is a serial DTE device, such another DTE device (PC, for

example) requires a “null modem” cable. If connecting the EC-BOS-6

to a DCE device (modem, for

example), a straight-through cable is used.

Table 3

provides standard serial DB-9 pinouts.

Battery in bracket
(on top of option
cards, if any)

EC-BOS

Battery

20 Pin Connector

(Power Modules)

Ethernet (RJ-45)

LAN 2

RS-232

(DB-9)
COM1

Primary

Ethernet (RJ-45)

LAN 1

RS-485
(3-pos.)

COM2

Earth Ground

Spade Lug

Barrel power
connector for
EC-WPM-XX

Option Slot area
(Slot #1 this side)

s + –

Содержание EC-BOS-6AX





























Результаты поиска

Содержание EC-BOS-6AX

Отзывы:

Похожие инструкции для EC-BOS-6AX

Бренды по названию

Популярные бренды

Distech Controls EC-BOS-6AX, Монтаж и подключение

Результаты поиска

Содержание EC-BOS-6AX

Отзывы:

Похожие инструкции для EC-BOS-6AX

Бренды по названию

Популярные бренды