Distech Controls EC-BOS-6AX Скачать руководство пользователя страница 16

Страница: 16 / 28

EC-BOS-6

Mounting and Wiring Instructions

Revised: February 2008

Part Number: 05DI-HIBS6AX-10

Power Up and Initial Checkout

Communications Wiring

Note

If a modem option card (EC-NPB-MDM) is installed, this port becomes disabled—except if rebooted
with the mode jumper (see

Figure 2

on page 7) in the “Serial Shell” position.

RS-485—

An RS-485, optically isolated port uses a 3-position, screw terminal connector and always operates

as COM2. Wire to this connector with shielded 18-22AWG wiring (refer to the TIA/EIA-485 standard). As
shown in

Table 3

, the screw terminals (from left-to-right) are shield, plus (+), and minus (–).

USB—

A single USB port is on the top of the board.

Note

The USB port is for future use.

Power Up and Initial Checkout

Ensure power wiring to the EC-BOS-6

is ready—see the

“Power Wiring”

section on page 11. Refer to

Figure 2

on page 7 for the locations of the EC-BOS-6

battery connector, status LEDs and barrel power

connector (for EC-WPM-

only). Refer to

Figure 3

on page 13 for location of the power connector on the

EC-NPB-PWR/-UN power module.

Following all mounting and wiring, perform the following:

Procedure 4

Initial power up and checkout

Step 1

Connect the Backup Battery

Step 2

Apply Power

Step 3

Check the Status LEDs

Table 3

Serial port (RS-232 and RS-485) pinouts.

Base RS-232 DB-9 Port (COM1)

Base RS-485 Port (COM2)

Pinout References

Signal

DB-9 Plug Pin

Pinouts

DCD

Data carrier detect

RXD

Receive data

TXD

Transmit data

DTR

Data terminal ready

GND

Ground

DSR

Data set ready

RTS

Request to send

CTS

Clear to send

not used on the EC-BOS-6

DB-9 Plug

(male)

3-position connector

(male)

S + –

Содержание EC-BOS-6AX





























Результаты поиска

Содержание EC-BOS-6AX

Отзывы:

Похожие инструкции для EC-BOS-6AX

Бренды по названию

Популярные бренды

Distech Controls EC-BOS-6AX, Монтаж и подключение

Результаты поиска

Содержание EC-BOS-6AX

Отзывы:

Похожие инструкции для EC-BOS-6AX

Бренды по названию

Популярные бренды