Distech Controls EC-BOS-6AX Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 28

background image

EC-BOS-6

AX

Mounting and Wiring Instructions

Revised: February 2008

Part Number: 05DI-HIBS6AX-10

Certifications

Federal Communications Commission (FCC)

24

Certifications

Federal Communications Commission (FCC)

This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in
accordance with the instruction manual, may cause interference with radio communications. It has been tested
and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC
Rules, which are designed to provide reasonable protection against such interference when operated in a
commercial environment. Operation of this equipment in a residential area may cause interference, in which
case, users at their own expense will be required to take whatever measures may be required to correct the
interference. Any unauthorized modification of this equipment may result in the revocation of the owner's
authority to continue its operation.

Canadian Department of Communications (DOC)

Note

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.

Note

Cet appareil numérique de la classe A respecte toutes les exigences du Règlement canadien sur le
matèriel pouvant causer des interfèrences.

«
...
22
23
24
25
26
...
»

Содержание EC-BOS-6AX





























Отзывы:

Нет отзывов

Похожие инструкции для EC-BOS-6AX

Бренд: National Instruments Страницы: 10

Evolution Series E9000

Бренд: GE Страницы: 44

PACSystems RX7i

Бренд: GE Страницы: 469

GuardSwitch 300 Series

Бренд: GE Страницы: 2

GuardSwitch 300 Series

Бренд: GE Страницы: 2

Masoneilan VariPak 28001

Бренд: GE Страницы: 24

Бренд: Aalborg Страницы: 128

AirGENIO SUPERIOR

Бренд: 2VV Страницы: 27

Бренд: 2N Страницы: 91

Бренд: Jafar Страницы: 10

Бренд: GBD Страницы: 68

Бренд: Harman Страницы: 2

Бренд: T-Link Страницы: 3

Бренд: Jandy Страницы: 28

Бренд: Jands Страницы: 6

Бренд: jbc Страницы: 4

Бренд: jbc Страницы: 4

Grafica DNE-K07

Бренд: Paradox Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды