background image

 

SKM-13-0060

 

D

ET 

N

ORSKE 

V

ERITAS 

DECLARATION OF COMPLIANCE

 

This is to declare that the food waste disposer equipment for installation as garbage handling equipment 
on ships and floating platforms, DISPERATOR models 510, 515, 520, 530, 550 & 575 manufactured by 
Disperator AB are in compliance with applicable sections of MARPOL consolidated edition 2011/2012, 

ANNEX V REGULATIONS FOR THE CONTROL OF POLLUTION BY GARBAGE FROM SHIPS. 

Regulation 4

 

Discharge of garbage outside special areas

 

1

 

Subject to the provisions of regulations 5, 6, and 7 of this Annex, discharge of the following garbage into the sea 

outside special areas shall only be permitted while the ship is en route and as far as practicable from the nearest land, but in any 
case not less than: 

.1 

3 nautical miles from the nearest land for food wastes which have been passed through a comminuter or 

grinder.  Such comminuted or ground food wastes shall be capable of passing through a screen with openings no 
greater than 25 mm. 

Regulation 5

 

Special requirements  for discharge of garbage from fixed or floating platforms

 

2

 

Food wastes may be discharged into the sea from fixed or floating platforms located more than 12 nautical miles from 

the nearest land and from all other ships when alongside or within 500 m of such platforms, but only when the wastes have 
been passed through a comminuter or grinder.  Such comminuted or ground food wastes shall be capable of passing through a 
screen with openings no greater than 25 mm. 

Regulation 6

 

Discharge of garbage within special areas

 

Discharge of the following garbage into the sea within special areas shall only be permitted while the ship is en route 

and as follows: 

.1 

Discharge into the sea of food wastes as far as practicable from the nearest land, but not less than 12 nautical 

miles from the nearest land or the nearest ice shelf.  Food wastes shall be comminuted or ground and shall be capable 
of passing through a screen with openings no greater than 25 mm.  Food wastes shall not be contaminated by any 
other garbage type. 

For Det Norske Verirtas AB 

AnnaBerglund 
Senior Surveyor 

 

Digitally Signed By: Berglund, Anna 

Location: DNV Stockholm 
Signing Date: 2013-06-11 

If any person suffers loss or damage which is proved to have been caused by any negligent act or omission of Det Norske Veritas, then Det Norske Veritas shall pay compensation to such person for his proved direct loss or 
damage. However, the compensation shall not exceed an amount equal to ten times the fee cha rged for the service in question, provided that the maximum compensation shall never exceed USD 2 million. 
In this provision "Det Norske Veritas" shall mean the Foundation Det Norske Veritas as well as all its subsidiaries, directors, officers, employees, agents and any other acting on behalf of Det Norske Veritas. 

D

ET 

N

ORSKE 

V

ERITAS AS, 

Veritasveien 1, NO-1322 Høvik, Norway, Telephone: +47 67 57 99 00, Telefax: +47 67 57 99 11, Org.No. NO 945 748 931 MVA

Form No.: 40.91a 

Issue: January 2008 

Содержание EXCELLENT Series


































Отзывы: