of
10
12
Utility Mode
The final mode on the DMC.micro is for the tweakers - this mode allows you to send just about any MIDI message you want to your
devices. It requires some careful setup, but once that’s done you’ve got all kinds of control!
To use Utility Mode, enter the DMC setup and configure UTIL = ON.
Next, you will need to set up the Utility parameters you’d like to use.
U Lt
Utility Mode, Left Button Message Type.
This sets the type of message that the left button will send.
ONE:
MIDI CC message will be sent with the same value each time the button is pressed.
TOGG:
MIDI CC message will be sent with two alternating values when the button is pressed.
NOTE:
MIDI Note on and note off message will be sent when the button is pressed.
b UP:
Bank up message will be sent for Strymon devices.
b DN:
Bank down message will be sent for Strymon devices.
TAP:
Tap tempo message will be sent - the DMC.micro knows which messages are required for this!
U Ln
Utility Mode, Left Button Message Number.
This sets the MIDI CC controller number or MIDI note number that the left button will send.
Ranges from 0-127.
U LL
Utility Mode, Left Button Low Value.
This sets the MIDI CC lower number for use with the Toggle message type.
U LH
Utility Mode, Left Button High Value.
This sets the MIDI CC upper value for use with the Toggle message type, or the value sent for the
ONE shot message type. Also sets the velocity of the MIDI note sent for the NOTE message type.
U LC
Utility Mode, Left Button Channel.
This sets the MIDI channel or channels that the left button will use to send messages. The channel is
indicated with the letters A, B, C. If you wish to send a message to the A, B, or C device its letter must be shown. If a zero is shown in a particular
location, that channel will not receive the messages from this button. For example, U LC = AB0 means that the left button in Utility Mode will send MIDI
messages to Devices A and B but not to Device C.
U r t
Utility Mode, Right Button Message Type.
This sets the type of message that the right button will send.
Options are identical to the Left Button Message Type above.
U r n
Utility Mode, Right Button Message Number.
This sets the MIDI CC controller number or MIDI note number that the right button will send.
Ranges from 0-127.
U r L
Utility Mode, Right Button Message Low Value.
This sets the MIDI CC lower number for use with the Toggle message type.
U r H
Utility Mode, Right button High Value.
This sets the MIDI CC upper value for use with the Toggle message type, or the value sent for the
ONE shot message type. Also sets the velocity of the MIDI note sent for the NOTE message type.
U r C
Utility Mode, Right Button Channel.
This sets the MIDI channel or channels that the right button will use to send messages. The options
are identical to the Utility Mode Left Button Channel above.
U At
Utility Mode, Alternate Button Message Type.
This sets the type of message that the left button will send
when held down
.
ONE:
MIDI CC message will be sent with the same value each time the button is pressed.
TOGG:
MIDI CC message will be sent with two alternating values when the button is pressed.
NOTE:
MIDI Note on and note off message will be sent when the button is pressed.
b UP:
Bank up message will be sent for Strymon devices.
b DN:
Bank down message will be sent for Strymon devices.
U An
Utility Mode, Alternate Button Message Number.
This sets the MIDI CC controller number or MIDI note number that the left button will
send
when held
. Ranges from 0-127.
U AL
Utility Mode, Alternate Button Low Value.
This sets the MIDI CC lower number for use with the Toggle message type.
U AH
Utility Mode, Alternate Button High Value.
This sets the MIDI CC upper value for use with the Toggle message type, or the value sent for
the ONE shot message type. Also sets the velocity of the MIDI note sent for the NOTE message type.
U AC
Utility Mode, Alternate Button Channel.
This sets the MIDI channel or channels that the left button will use to send messages
when held
.
The options are identical to the Utility Mode Left Button Channel above.
Finally, save and exit setup. Navigate to the UTIL page and you’re done! Tap the left or right button to send the messages you chose
in setup, or hold the left button to send the Alt messages. If any of your message types are set to TOGGle, the DMC LEDs will light to
show the toggle status.
Disaster Area Designs
DMC.micro
Gen3
Содержание DMC.micro
Страница 1: ...DMC micro User Manual v1 00c...
