DirecTV Advanced Installation Meter 2 Скачать руководство пользователя страница 9

Страница: 9 / 108

Page 9

AIM 2 Operation Manual

How this Manual is Organized

This manual is divided into the following chapters:

• Chapter 1: General Information

provides Trilithic contact information and describes

how this operation manual is structured.

• Chapter 2: Introduction

introduces what the AIM is and what it does. This chapter

discusses the practical application, connections and controls of the AIM. Finally, this

chapter discusses the battery of the AIM and how to update your firmware.

• Chapter 3: Getting to Know Your Meter

describes a brief overview of the features,

buttons, and controls of the AIM.

• Chapter 4: Setting Up the Meter

describes how to configure and operate the AIM. This

chapter provides instructions for entering registration information, as well as setting the

meter’s volume, display contrast and brightness, time limits for power-saving features,

and date and time.

• Chapter 5: Setting Up a Job

describes the steps needed to set up the information for

the installation job. This chapter provides instructions for entering the account number,

selecting the ODU type, selecting the switch type, and entering the zip code.Chapter 5,

“Appendix” shows the technical specifications of the AIM as well as any error codes that

may appear on the display screen of the AIM.

• Chapter 6: Installing an ODU

describes the steps needed for aligning and performing

follow-up Extended Installation Verification (EIV) for each ODU. This chapter provides

instructions for how to complete these processes using the AIM.

• Chapter 7: Performing EIV

describes the steps needed to perform Extended

Installation Verification (EIV) at selected points in the distribution network to quickly

confirm that the installation is satisfactory for all supported orbital slots. EIV is an easy

way to pinpoint any potential problems with the installation. This chapter provides

instructions for performing EIV at the ODU and other locations in the distribution

network.

• Chapter 8: Performing Other Network Tests

describes the steps to The AIM stores

records for tests performed on the AIM, as well as screenshots. This chapter provides

instructions for how to view records, delete records, and transfer records to or from the

AIM using a USB flash drive.

Содержание Advanced Installation Meter 2













































































































Результаты поиска

Содержание Advanced Installation Meter 2

Отзывы:

Похожие инструкции для Advanced Installation Meter 2

Бренды по названию

Популярные бренды

DirecTV Advanced Installation Meter 2, Руководство по эксплуатации

Результаты поиска

Содержание Advanced Installation Meter 2

Отзывы:

Похожие инструкции для Advanced Installation Meter 2

Бренды по названию

Популярные бренды