DirecTV Advanced Installation Meter 2 Скачать руководство пользователя страница 79

Страница: 79 / 108

Page 79

AIM 2 Operation Manual

Connect the AIM ODU F connector at the

location in the distribution network where you

want to test.

To test between the ODU and the multiswitch,

disconnect the cable connecting the ODU to

the multiswitch and connect it to the AIM’s ODU

F connector.

7. Press

NEXT

to go to the

SAT TUNE

screen.

8. If the installation includes two ODUs, highlight

the ODU to test and press

SELECT

continue.

9. Highlight the orbital slot to test or use the

keypad to enter the slot number, and press

SELECT

to continue.

10.

If you want to set the SWiM (or DSWiM)

channel for the test, do the following:

• Press

OPTIONS

• On the

SAT TUNE OPTIONS

screen,

press

SELECT

to select

Set SWiM Ch.

(Connect SWiM)

• Highlight the desired channel and press

SELECT.

11. Highlight the transponder to test. Then press

SELECT

and wait briefly for the results of the

test.

You also can use the keypad to enter the

transponder number. Use

PAGE UP

PAGE

to scroll quickly through the transponders.

Содержание Advanced Installation Meter 2













































































































Результаты поиска

Содержание Advanced Installation Meter 2

Отзывы:

Похожие инструкции для Advanced Installation Meter 2

Бренды по названию

Популярные бренды

DirecTV Advanced Installation Meter 2, Руководство по эксплуатации

Результаты поиска

Содержание Advanced Installation Meter 2

Отзывы:

Похожие инструкции для Advanced Installation Meter 2

Бренды по названию

Популярные бренды