Dinstar SBC1000 Скачать руководство пользователя страница 41

Страница: 41 / 71

3 Configurations on Web Interface

SBC1000 Session Border Controller

IP Range

Configure the range of legal IP addresses that send out SIP request can be received by

the

Mask

The subnet mask of the IP range

Signaling DSCP

The QoS tag of SIP signaling messages

Media DSCP

The QoS tag of meida messages

Near-end NAT

Near-end NAT defaults to disabled. If it is enabled, the contact IP address contained in

SIP messages sent out by SBC1000 will be turned into the outbound IP address of public

network.

If NAT is enabled, you need to fill in the outbound IP address of public network.

Domain Filter

Rate Limit

The maximum RPS(registrations per second), CPS(calls per second) and total call

volume. Please refer to3.4.5

Codec

The codecs that the access network supports. Please refer to 3.4.7

Blacklist

Select a blacklist for the access network. Calls given by the caller numbers on the

blacklist will be refused to go through the access network. Please refer to 3.4.6

Whitelist

Select a whitelist for the access network. Calls initiated by the caller numbers on the

whitelist will be allowed to go through the access network. Please refer to 3.4.6

If no black list and white list are selected for the access network, all calls are allowed to

go through the access network

Inbound

Manipulation

Select a number manipulation rule or a number pool for the access network. When a call

coming into the access network matches the manipulation rule, its number will be

manipulated. Please refer to 3.4.8 and 3.4.9

DTMF

DTMF is short for Dual Tone Multi Frequency;

There are three DTMF modes, including SIP Info, INBAND, RFC2833;

If the DTMF mode of an access network differs from that of core network, SBC1000

will convert it through DSP

Inbound

SIP

Header

Manipulation

Select a SIP header manipulation rule for inbound calls of the access network. If a call

matches the manipulation rule, the SIP header of the messages related to the call will be

manipulated when it comes into the access network.

Please refer to 3.4.10

Outbound

SIP

Header

Manipulation

Select a SIP header manipulation rule for outbound calls of the access network. If a call

matches the manipulation rule, the SIP header of the messages related to the call will be

manipulated when it goes out the access network.

Please refer to 3.4.10

SIP

Session

Timer

Session timer is a mechanism to keep activating sessions.

If ‘Supported’ is selected, SBC1000 will send ‘reinvite’ messages to keep activating

Содержание SBC1000







































































Результаты поиска

Содержание SBC1000

Отзывы:

Бренды по названию

Популярные бренды

Dinstar SBC1000, Руководство пользователя

Результаты поиска

Содержание SBC1000

Отзывы:

Бренды по названию

Популярные бренды