Digitrax DCS210+ Скачать руководство пользователя

Страница: 8 / 32

www.digitrax.com

3.0 Operating on batteries without LocoNet cable

All DT602 models can operate unplugged in IR tetherless (without wires)

mode if they detect Digitrax Infra-Red (IR) capability when first plugged into

a working LocoNet. The DT602D can additionally operate in wireless Digitrax

Duplex mode if it detects Duplex capability when first plugged into LocoNet.

To operate a tetherless mode you will need to install three AA size 1.5V batter-

ies in correct orientation in the rear battery compartment. After disconnecting

a battery-powered DT602 from LocoNet, the throttle will enter the tetherless

mode it and the LocoNet system is configured for, IR or Duplex.

The DT602D/DE (Duplex) versions can perform most of its tethered or

plugged-in functions while they are untethered, after initial plug-in to configure

Duplex settings. Duplex throttles will automatically reconnect to the LocoNet

system when disconnected or powered up again untethered.

Duplex mode active will show the Digitrax NetName in the STATUS line

left-side in black text, along with the signal strength bars, Channel number

and Battery level. If a Duplex message fails to get through the white LED

will flash, and if layout Duplex support fails the current NetName display will

change to red text.

3.1 Recharging a Digitrax BP600MH Battery pack

1. Remove the 3 AA batteries from the DT602 rear compartment and plug

the 3 pin plug from an optional BP600MH battery pack into the matching

socket. The yellow lead will be closest to the DT602 bottom edge. Form

the wires to the compartment lower area and then replace the compartment

lid with the battery and wires secure inside.

2. Plug in an external 10V to 18V DC supply (100mA minimum) with a 2mm

center-positive plug into the charging socket at DT602 bottom edge.

3. Press the

key until you get the “Charge” text above

key, then

press this key again

4. The DT602 will enter charge mode and typically automatically stop after

about 14 hours. When in a charging IDLE mode the

key will flash red

about every 3 seconds. Charge time depends on the battery history, like;

residual charge, temperature and tolerances etc.

3.2 Powering a DT602 OFF

To power OFF a DT602 that is

untethered

before the normal inactivity power

OFF timeout, press the

key and then the soft

key to power OFF com-

pletely.

In this state the DT602 will draw no battery power, and can be re-powered by

simply pressing the

key again. The DT602 will not power down when on

an active LocoNet or plugged into DC for charging.

Содержание DCS210+

































Результаты поиска

Содержание DCS210+

Отзывы:

Похожие инструкции для DCS210+

Бренды по названию

Популярные бренды

Digitrax DCS210+, Руководство пользователя

Результаты поиска

Содержание DCS210+

Отзывы:

Похожие инструкции для DCS210+

Бренды по названию

Популярные бренды