Digitrax DCS210+ Скачать руководство пользователя страница 20

Страница: 20 / 32

www.digitrax.com

keypad to select the method of programming

you wish to use by pressing the correspond-

ing number.

•  1-Po; Ops on Mainline
•  2-Pd; Direct on Prg Trk
•  3-Pg: Paged on Prg Trk
•  4-Ph: Physical on Prg Trk
Note: Direct programming is the Digitrax pre-

ferred method
5. Once you have selected a programming

method, it will be listed above entries for

CV number and CV data. CV number is the

number of the CV you are changing. CV data

is the value you are programming to the CV number.

6. To change the CV number you are editing

press the

“CVNUM”, then use the keypad

to enter the CV number you want to change.

7. Once you have the CV number selected press

the

“CVDATA”. The soft keys will

change to “WRITE”, “READ”, and “BACK”.

Press the

“READ” to read the current

value of the CV number you have selected.

Use the keypad to enter the value you wish to

program to the CV number you have selected.

Press the

“WRITE” to save the data

entered. The

Scrolling Help Text

line will

read “Program Task OK” when it has success-

fully programmed the value.

8. Press

“BACK” to exit to the previous menu to select another CV to

change if you wish. If you are done editing CVs press

“DONE” to

return to normal operations.

7.2.1 Programming On The Mainline

Operations (OPS) Mode Programming

lets you program CVs in DCC loco-

motives equipped with extended packet format decoders while they are running

on the mainline. A typical use for OPS mode programming would be to change

the acceleration rate (CV03) or the deceleration rate (CV04) of your locomo-

tives to simulate the weight and braking capability of the train to compensate

for changing the number of cars or power units on a train.

Your DT602 can use OPS Mode Programming to change the CV value in ANY

CV, including 2 digit and 4 digit addresses, but some decoders may not accept

changing these CVs in Operations mode.

How to use Operations Mode Programming:

1. Make sure the loco you want to program is on the powered up mainline

connected to the Rail A and B terminals of your command station.

CV Program Menu A:

2- Pd; Direct on Prg Trk

CV Number:

CV data:

0001

Trk

USB

CVNUM

CVDATA

DONE

CV Program Menu A:

0- Last Menu

1- Po; Ops on Mainline

2- Pd; Direct on Prg Trk

3- Pg; Paged on Prg Trk

4- Ph; Physical on Prg Trk

CVNUM CVDATA

DONE

Содержание DCS210+

































Результаты поиска

Содержание DCS210+

Отзывы:

Похожие инструкции для DCS210+

Бренды по названию

Популярные бренды

Digitrax DCS210+, Руководство пользователя

Результаты поиска

Содержание DCS210+

Отзывы:

Похожие инструкции для DCS210+

Бренды по названию

Популярные бренды