background image

Operator's Manual

DS7A - Constant Current Stimulator

Recommended separation distances between portable & mobile RF 
communications equipment & the Digitimer DS7A (Table 6)

The Digitimer DS7A is intended for use in an electromagnetic environment in which radiated RF 
disturbances are controlled. The customer or the user of the Digitimer DS7A can help prevent 
electromagnetic interference by maintaining a minimum distance between portable and mobile RF 
communications equipment (transmitters) and the Digitimer DS7A as recommended below, 
according to the maximum output power of the communications equipment.

Rated maximum

output power of

transmitter (W)

Separation distance according to frequency of transmitter (m)

150 kHz to 80 MHz

d = [3,5/3] 

Å

P

80 MHz to 800 MHz

d = [3,5/3] 

Å

P

800 MHz to 2.5 GHz

d = [7/3] 

Å

P

0.01

0.12

0.12

0.23

0.1

0.37

0.37

0.74

1

1.12

1.12

2.33

10

2.88

2.88

5.76

100

11.67

11.67

23.33

For transmitters rated at a maximum output power not listed above, the recommended separation 
distance 

d

 in metres (m) can be estimated using the equation applicable to the frequency of the 

transmitter, where 

P

 is the maximum output power rating of the transmitter in watts (W) according 

to the transmitter manufacturer.

NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.

NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by 
absorption and reflection from structures, objects and people.

Digitimer Ltd.

55 of 58

Copyright © 2014

File Ref: N:\Docs\Company\Manuals\DS7A\Issue-14\DS7A-iss14.odt

Last Revised: February 1, 2017

Содержание DS7A



























































Отзывы: