Digitimer DS7A Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 58

background image

Operator's Manual

DS7A - Constant Current Stimulator

Appendix 3 .. Operational Tests

These tests are to be

performed only by qualified personnel

.

There should be no patient connection during these tests.

Connect a 100R resistor (1/2W) in series with a power resistor in the range 2000 to 3000 ohms (5 watts or
greater) across the output terminals. Monitor the potential across the 100R resistor. Note the 100R should
be connected to the positive terminal which is the common terminal of the oscilloscope monitor. See circuit
below.

Using a repetitive trigger (except for test 5) and pulse polarity set to “Normal” :

1. With SW1 open set voltage control to 400V, pulse duration 1000 microseconds and current control

to 100 mA (maximum CW, x10 range). Trigger DS7A and record stimulus output potential
generated across the 100R resistor - should be 10 volts peak, 1 ms wide. Check that the amber
"Trigger" indicator is turned on.

2. Now close SW1 and check that potential across 100R resistor has not changed appreciably.
3. With SW1 reopened reduce voltage control until potential across 100R resistor reduces. Check then

that the amber "out of compliance" indicator is turned on.

4. Now switch the current range from x10 to x1 and check that potential across 100R resistor falls from

10 volts peak to 1 volt peak.

5. Check that all three methods of triggering operate correctly.

a) Manual front panel switch
b) Foot switch through rear panel jack socket
c) Electrical pulse trigger through rear panel Trigger-In BNC socket.

6. Check that there is a Trigger Output pulse coincident with the stimulus pulse.

Digitimer Ltd.

49 of 58

Copyright © 2014

File Ref: N:\Docs\Company\Manuals\DS7A\Issue-14\DS7A-iss14.odt

Last Revised: February 1, 2017

3k

100R

CRO

SW1

+

-

DS7A

«
...
47
48
49
50
51
...
»

Содержание DS7A



























































Отзывы:

Нет отзывов

Похожие инструкции для DS7A

Бренд: R.M. Young Страницы: 2

NANOCOLOR UV/VIS II

Бренд: Macherey-Nagel Страницы: 99

Бренд: Xantrex Страницы: 2

Бренд: Xaoc Devices Страницы: 8

Бренд: WATERGUARD Страницы: 2

Бренд: Yamaha Страницы: 10

Бренд: Yamaha Страницы: 38

Бренд: Yamaha Страницы: 45

Бренд: HANSA-FLEX Страницы: 23

Бренд: RS PRO Страницы: 44

Бренд: Feature tech Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Zero 88 Страницы: 32

Micropilot S FMR533

Бренд: E+H Страницы: 12

Бренд: National Instruments Страницы: 169

Бренд: Kirby Morgan Страницы: 101

Бренд: BASI Страницы: 69

Friendly Digital Piano Forte PV35

Бренд: Kawai Страницы: 102

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды