Specifications subject to change without notice
© Digital View Ltd – Doc Ver 1.7: 23 April, 2014 (SGX-1920_manual.doc)
Page
5 of 70
11. Second RS-232 control interface :
This interface support controlled under “Programming mode” .
Press and hold “MENU” button on the OSD switch mount and turn on the controller to enter the “Programming mode”.
Choose “Set Uart 1 Input Port” shown below :
.
Set “Uart 1 to IP-50 : Enable Ethernet network (J1) support and disable second RS-232 serial control (CN1) support
Set “Uart 1 to CN1 : Enable second RS-232 serial control (CN1) support. Disable Ethernet network (J1) support
12. External panel power output
: User for specific panel model.
13. Panel control signal :
Use for specific panel model.
14. Audio add-on board P/N 416940020-3
: Provide the interface for the audio add-on board P/N 416940020-3 to be
connected. The audio add-on board gives the audio input and output signal connection. The volume can be controlled by
the OSD menu on the controller. It is an optional part only, can be unconnected if not using audio.
CAUTION : The Audio Add-on Board P/N 416940020-3 is only operate under 12VDC power input environment.
15. Aux5VDC output :
2 ways connector pr5VDC output.
16. Ambient light sensor connection :
3 ways connector provides interface for ambient light sensor connection by using Kit
70220-3.
17. Backlight status input :
2 ways connector provides interface for connection with the specific panel type which support the
panel with backlight status monitoring function.
18. Auxiliary video input
: It provides alternate video input for S-Video 1, Composite Video 1 & Component Video 1. And it
also provide S-Video 2, Composite Video 2 & Component Video 2 input. Plug the auxiliary video cable P/N 426301700-3 on
CNV5 connector.
19. Auxiliary Digital Input Port – HD1 :
Support Digital video signal input (e.g HDMI, DVI, HD-SDI (from HD-1000/-2000/-
3000/-3000S)). Please refer to Appendix IX to configure this auxiliary digital input port – HD1. Reasonable quality cable
should be used to avoid image quality degradation.
20. Auxiliary Digital Input Port – HD2 :
Support Digital video signal input (e.g HDMI, DVI, HD-SDI (from HD-1000/-2000/-
3000/-3000S)). Please refer to Appendix IX to configure this auxiliary digital input port – HD2. Reasonable quality cable
should be used to avoid image quality degradation.
21. Reserved :
No function, reserved for future development.
22. HDMI audio output :
Support HDMI audio with stereo output.
The HDMI audio output can be connected to Audio add-on board P/N 416940020-3 by using the audio cable P/N
426451800-3 (310mm) connected between SGX-1920 (connector : CN10) and Audio add-on board P/N 416940020-3
(connector : CN2).
23. SPDIF Audio output :
This port support SPDIF audio output from the HDMI audio source inputted.
24. DVI-D input cable :
Plug the DVI cable to the connector P3 on the controller board.
25. HDMI input :
Plug the HDMI cable to the connector P2 on the controller board. This port is not supported when CN5 is
connected.
26. Analog RGB Input
: As this may affect regulatory emission test results and the quality of the signal to the controller a
suitably shielded cable should be utilized.
27. Control over network connection :
This is a network device that allow to control RS-232 enable devices over a TCP/IP
based Ethernet and the Internet using a web browser. Please refer to Appendix VIII in details.
28. Power Input
: 12V/24VDC is required, this should be a regulated supply. The power rating is depending on the panel and
Downloaded from
Downloaded from
Downloaded from
Downloaded from
Downloaded from
