background image

XR2500F User’s Guide 

Introduction

Introduction 

XR2500F User’s Guide 

5

Remote Fire Command Center 

You can expand the XR2500F Addressable Fire Alarm Control Panel 

by adding a Remote Fire Command Center.  With the Remote Fire 

Command Center, users can access the User Menu and perform the 

same functions as the Fire Command Center in the panel enclosure.  

All of the keys, except the four function keys, can be used at any 

time without turning the keyswitch.
You  can  only  use  the  four  function  keys  when  the  keyswitch  is 

turned to the enable position.  These keys are the same as those on 

the Fire Command Center in the panel.  Both keyboards also have 

the same displays and prompts.  Follow the same instructions for 

using both keyboards.
Below  is  an  illustration  of  the  Remote  Fire  Command  Center 

showing the keyswitch lock that enables the four function keys.

���������

�����

�������

�����

�������

���

���

���

���

���

���

���

���

��

������

�������

�����

����

�����

�������������������

�����������

�����������

�����������

�������������

���������������

��������������

�����������

Special Fire Command Center Displays

As you use your system, you occasionally see a display that asks you 

to enter a code or that describes a condition on the system.  Below 

are some examples of the displays:

ALARM

A  24-hour  zone  (for  example  fire  or  panic)  or  an  armed  burglary 

zone has been tripped.  Your system may sound bells or sirens.

ALARM NOT SENT

The alarm signal was not sent to the central station because a user 

code was entered to disarm the system before the alarm signal was 

sent to the centralstation.

ALARM CANCELLED

An  Alarm  Cancel  signal  was  sent  to  the  central  station  because 

a  user  code  was  entered  after  an  alarm  was  sent  to  the  central 

station.

TROUBLE

There is a problem with a protection device or system component.  

This display is accompanied by a description of the problem.

ENTER CODE

The system requires you to enter your user code.  User codes can 

be  required  for  turning  your  system  on  (arming),  turning  your 

system off (disarming), and many other functions.
As you enter your user code, the keypad display shows an asterisk 

(*) in place of each digit pressed.  This keeps others from seeing 

your user code on the display as it is entered.

TRY AGAIN or INVALID CODE

The user code you have entered is not recognized by the system.  

Check the user code and try again.

Содержание XR2500F





































Отзывы: