Digital Equipment VAX 4000 500A Скачать руководство пользователя страница 104

Страница: 104 / 140

7. The system displays a list of the local devices on your system; for example:

Available device MIA5:

device type TK85

Available device DIA0:

device type RF31

.
.
.

8. When standalone BACKUP finishes booting, it displays an identification

message followed by the dollar-sign prompt ($):

%BACKUP-I-IDENT, stand-alone BACKUP V5.5--n; the date is

19-APR-1991 13:00:00.00

9. Remove the tape cartridge containing standalone BACKUP from the tape

cartridge drive.

To back up the system disk, see Section B.2.
To restore the system disk, see Section B.3.

B.2 Backing Up the System Disk

The reasons to back up a system disk are:
• In case a problem occurs during a VMS upgrade or update, or during the

installation of other software products. Before you attempt any of these

procedures, you should back up the system disk. If a problem occurs, you can

restore the backup copy of the system disk.

• To prevent loss of system files if they are deleted accidentally. After you

install or upgrade the VMS operating system or any other software products,

you should back up the system disk. If a system file is deleted and renders

the system disk inoperable, you can restore the backup copy and continue to

use the system.

• In case the system disk malfunctions. If you have a backup copy of the VMS

operating system, you can restore it to a functioning disk and continue to use

the system.

• To eliminate disk fragmentation. It happens when files are not stored

contiguously on the disk. Back up the system disk to a tape cartridge,

diskettes, or another disk. Then restore the files to the original system disk.

The BACKUP command creates a copy on which files are stored contiguously.

B–6 Backup Procedures

Содержание VAX 4000 500A













































































































































Результаты поиска

Содержание VAX 4000 500A

Отзывы:

Похожие инструкции для VAX 4000 500A

Бренды по названию

Популярные бренды

Digital Equipment VAX 4000 500A, Операция

Результаты поиска

Содержание VAX 4000 500A

Отзывы:

Похожие инструкции для VAX 4000 500A

Бренды по названию

Популярные бренды