12
Setting the Time Range (xx.xx or x.xxx)
The Time Range controls the resolution of the first and second stages times only.
The first and second stage times can
be set to any number from 0.000 to 9.999 seconds when in “x.xxx” Range and from 00.00 to 99.99 seconds when in “xx.xx” Range.
The settings for Pro Timer 1 and for Pro Timer 2 do not have to be the same. However care should be taken to notice the decimal
point location when entering a stage time. To change the Time Range on the Pro Screen, the selection arrows must first be on either
line 2 or 3. If the selection arrows are not on line 2 or 3 use the Next key until line 2 has been selected. Next press and hold the
number
8
key until the decimal point moves to desired location. Setting the Time Range for Pro Timer 2 is explained on page 13.
Setting Stage Times
To enter a new stage time, first using the Next key move the selection arrows to the line to be changed, line 2 for Stage 1 or
line 3 for Stage 2. Once the desired line has been selected press and release the Clear key the selected display line will now be blank
indicating the unit is ready to accept the new time. Now using numerical keys enter the new time, leading zeros do not have to be
entered. For example if a time of 00.50 for a Stage 1 is desired, 50 would be entered on the keypad. If less than four digits are
entered for a time, pressing the Next key will act as an enter key and the leading zeros will displayed on the LCD. As the numbers
are entered they are shown on the display, indicating the numbers are accepted and entered into memory. If a mistake is made while
entering the time, press and release the Clear key and reenter the time again.
The Scrolling Arrow keys can also be used to change stage times. First make sure that the selection arrows are on the line to
be changed. If not change which line is selected using the Next key. Once the desired line has been selected pressing and releasing
the Up Arrow key will cause the time to increase by one. While pressing and releasing the Down Arrow key will cause the time to
decrease by one. If the Up Arrow key is held down the time will scroll up and if the Down Arrow key is held down the time will
scroll down.
Note: Entering all zeros into any stage turns that stage off.
Setting Throttle Modes
The words “off on” or “on off” to the left of the stage times indicate the two possible Throttle modes for Pro Timer 1 on the
Pro Screen. To change the Throttle mode, while the selection arrows are on either line 2 or line 3, press and hold down the zero key
until the words “off on” or “on off” to the left of the stage times change to the opposite setting. Then release the zero key, the
Throttle mode has now been changed. Each time the Zero key is pressed, held, and then released, the Throttle mode will switch
between the two modes. To prevent an accidental switch between the two Throttle modes when entering a new stage time, the Zero
key will be disabled for two seconds after the fourth number is entered for the new stage time.
Note: Any changes made to the Pro Timer 1 setting on the Pro Screen will be shown on Screen 2. Additionally any changes
made to Pro Timer 1 on Screen 2 will be shown on the Pro Screen.
Setting the Delay Time
To enter a new Delay time, first using the Next key move the selection arrows to line 4. Once line 4 has been selected, press
and release the Clear key, the Delay time will now be blank indicating the unit is ready to accept a new time. Now using numerical
keys enter the new time, leading zeros do not have to be entered. For example if 0.010 for a Delay time is desired 10 would be
entered on the keypad. If less than four digits are entered for a time, pressing the Next key will act as an enter key and the leading
zeros will displayed on the LCD. As the numbers are entered they are shown on the display, indicating the numbers are accepted and
entered into memory. If a mistake is made while entering the time, press and release the Clear key and reenter the time again.
The Scrolling Arrow keys can also be used to change the Delay time. First make sure that the selection arrows are on line 4.
If not, change which line is selected using the Next key. Once line 4 has been selected pressing and releasing the Up Arrow key will
cause the time to increase by one. While pressing and releasing the Down Arrow key will cause the time to decrease by one. If the
Up Arrow key is held down the time will scroll up and if the Down Arrow key is held down the time will scroll down.