Digi 70002405 Скачать руководство пользователя страница 126

Страница: 126 / 163

Configure the device using the ConnectPort LTS web interface

Administration

Digi ConnectPort LTS User Guide

126

Total/Used/Free Memory

: The amount of memory (RAM) available, currently in use, and

currently not being used.

Serial

The

Serial

page under

Administration

System Information

lists the serial ports and their

configuration status. Click a port to view detailed serial port information on the

Serial Port

Diagnostics

page.

Note

The ConnectPort LTS serial ports behave like DTE ports.

Outputs from the device: TxD (in 422/485 Full duplex TxD+ and TxD-), RTS, and DTR

Inputs to the device: RxD (in 422/485 Full duplex RxD+ and RxD-), CTS, DSR, and DCD

For pin-out information, see

ConnectPort® LTS 8/16/32 Quick Start Guide

Serial Port Diagnostics

The Serial Port Diagnostics page displays information on the current state of a serial port on your Digi
device.

Configuration

: The Configuration page displays the electrical interface (Port Type) and basic

serial settings.

Signals

: The Signals pane shows the state of serial port signals. The serial port signals are

green when asserted (on) and gray when not asserted (off). These signals are defined as

follows:

RTS

: Request To Send.

CTS

: Clear To Send.

DTR

: Data Terminal Ready.

DSR

: Data Set Ready.

DCD

: Data Carrier Detected.

Serial Statistics

: The Statistics section includes data counters and error tracking that will help

determine the quality of data that is being sent or received. If the error counters are

accumulating, you may have a problem with your Digi device server.

Total Data In

: Total number of data bytes received.

Total Data Out

: Total number of data bytes transmitted.

Overrun Errors

: Number of overrun errors—the next data character arrived before the

hardware could move the previous character.

Framing Errors

: Number of framing errors received—the received data did not have a valid

stop bit.

Parity Errors

: Number of parity errors—the received data did not have the correct parity

setting.

Breaks

: Number of break signals received.

Содержание 70002405




































































































































































Результаты поиска

Содержание 70002405

Отзывы:

Digi 70002405, Руководство пользователя, Страница: 126 / 163

Результаты поиска

Содержание 70002405

Отзывы: