background image

5.3.b DRAIN (Fig. 7) 

Fix the water drain pipe (10)

 

in the housing provided on the rear of the appliance 

(front for the 

flush-mounting models)

. Make sure that: 

• the pipe is a hose
• the internal diameter is 22 mm, as required
• the water drain hose is not throttled at any point throughout its length
• the drain hose slopes downwards by at least 15%

It is advisable to drain the water straight into an open drain trap. 

5.4 CONNECTION TO THE ELECTRICITY MAINS 

 

 IMPORTANT

:

 

the appliance must be connected to the electricity mains by professionally qualified personnel in

accordance with the Manufacturer’s instructions

 

before connecting the appliance to the electricity mains, make sure that the mains voltage rating
corresponds to the value indicated on the rating plate 

make sure that the appliance is connected to an efficient earthing system

make sure that the capacity of the power supply system suits the maximum power value indicated
on the rating plate of the appliance

if the appliance comes supplied with a plug, prepare a socket controlled by an omnipolar circuit-
breaker (7 in Fig. 4), with a contact-opening gap of not less than 3 mm, in accordance with national
safety standards currently in force. This switch must be equipped with fuses, with the associated
residual current device positioned in such a way as to be readily accessible. Insert the plug into the
socket controlled by the switch (7 in Fig. 4)

the plug must only be replaced by professionally qualified and authorized personnel, and the new
plug must comply with current national safety standards

if the appliance comes supplied without a plug and you wish to connect it permanently to the power
supply, prepare an omnipolar circuit-breaker (7 in Fig. 4), with a contact-opening gap of not less
than 3 mm, in accordance with national safety standards currently in force. This switch must be
equipped with fuses, with the associated residual current device positioned in such a way as to be
readily accessible. 

This operation must be carried out by a specialized technician

make sure that you fully uncoil the power supply cable and check that it is not crushed in any way

should the supply cable be damaged, it must be replaced by a specialized technician using a
special cable available from the Manufacturer or from the Technical Service Centres

6  START-UP 

6.1 CLEANING INTERNAL PARTS 

The appliance will have already been cleaned in the factory. However, you are advised to wash the 
internal parts again before using the appliance. Make sure that the power supply cable is unplugged 
before carrying out the above cleaning operation. 

See cleaning and sanitizing manual for information regarding cleaning operations.

 

For cleaning operations in general, use an ordinary detergent for washing dishes or a solution of water 
and vinegar. Rinse thoroughly with plenty of cold water and remove any ice that may have been 
produced during the first 5 cycles after cleaning, together with any ice present in the bin.  

It is advisable to avoid using abrasive detergents or powders, since these might damage the finish.  

6.2 START-UP  
When you start up the appliance the first time, or when you start it up again after a long period at 
a standstill, fill the basin manually with water (Fig. 8).

 

This filling operation must be carried out by opening the door, raising the flaps (if any) and pouring the 
water directly into the internal basin. 
In the cycles subsequent to the initial one, the appliance will be filled with water in a fully automatic way. 

Содержание ICE32A

















































Отзывы: