manualshive.com logo in svg

Dialogic DSI SS7G41, Руководство пользователя

Поделиться
Скачать
Dialogic DSI SS7G41 Скачать руководство пользователя страница 6

Dialogic

®

 DSI SS7G41 Signaling Server – SIU Mode Release Notes 

Release 2.3.9 

6 

3.5

 

Use of ITU-T links at 56kb/s 

This release includes a correction to allow ITU-T SS7 links to optionally 
operate at 56kb/s. Previously only ANSI links supported 56kb/s operation. 

3.6

 

SS7MD Link Congestion Count (IPY00118009) 

This release contains corrections to the operation of two per-link 
measurements for the SS7MD board, the ‘Congestion Count’ and ‘Tx 
Messages Discarded’. 

3.7

 

STSLP Command - SS7 Link Status 

This release corrects operation of the STSLP command to allow use of the 
LINK parameter to display status for a single link. 

3.8

 

Message Router - Alias Point Code (IPY00117354) 

Previously, if a Message Router concerned relationship was configured where 
the concerned entity was in a different Network Context from the Point Code 
it was concerned about an implicit route to an alias Point Code would be 
created in the Network Context of the concerned entity. Configuration of an 
SCCP RSP using this alias Point Code was rejected. This release corrects this 
issue and allows a SCCP RSP to route to an alias Point Code. 

3.9

 

Message Router – Concerned Entity 

This release corrects operation of Message Router Concerned Entity mapping 
in the case where the concerned domain is a User Part (ie 
CONC_DOMAIN=UPART) and the concerned entity is in a different network 
context to the affected entity (ie. CONC_NC != NC). Previously status 
indications were not passed to the user part in this case. 

3.10

 

Message Router – Message Priority 

This release corrects an issue that potentially resulted in message priority 
getting set to zero when a message passes through the Message Router 
Function. 

3.11

 

Message Router - Destination DPC (IPY00117249) 

This release corrects an issue introduced in Release 2.2.9 which prevented 
correct operation of the Message Router Destination DPC parameter when 
using 24 bit point codes. 

3.12

 

Message Router - Measurements 

This release corrects the ‘period’ reported in measurements for Message 
Router Origins, Routing Keys and Destinations. This applies both to the user 
interface and to periodic measurements files. 

3.13

 

SCCP Load Share Table - Dynamic Addition 

This release corrects an issue which prevented dynamic addition of an 
additional DPC to an SCCP Load Share Table. 

Содержание DSI SS7G41



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды