Dialogic 4000 Media Gateway Series Скачать руководство пользователя страница 54

Страница: 54 / 108

Cause Code Mapping With The Dialogic® Diva® SIPcontrolTM Software

page 54

Cause Code Mapping With The Dialogic

Diva

SIPcontrol

Software

If the Dialogic

Diva

SIPcontrol

software uses Microsoft

Office Communications Server 2007 as SIP peer,

the cause/response code tables are used as specified by Microsoft. See

Default cause code mapping for

Microsoft® Office Communications Server (OCS) 2007 SIP peers

on page 57 for a detailed list of cause/response

codes.

If the Diva SIPcontrol software does not use Microsoft

OCS 2007, the default cause/response code mapping is

used. See

Default cause code mapping

below for a detailed list of cause/response codes.

Default cause code mapping

The Dialogic

Diva

SIPcontrol

software includes a default cause/response code mapping table that includes

the most common cause codes according to RFC 3398 and RFC 4497. If you need to define a cause code mapping
other than in the table, you can configure it in the Cause Code Mapping Configuration.

For ISDN to SIP code mappings, see

ISDN cause code to SIP response code

below.

For SIP to ISDN code mappings, see

SIP response code to ISDN cause code

on page 55.

ISDN cause code to SIP response code

ISDN cause
code

Description

SIP response code
forwarded to the
SIP peer

Description

Unallocated number

404

Not found

No route to specified transit network

404

Not found

No route to destination

404

Not found

Normal call clearing

603

Decline (The PBX of Philips sends this code
during call set-up if the user rejects the
call.)

User busy

486

Busy here

No user response

603

Decline (The PBX of Philips sends this code
during call set-up if the user rejects the
call.)

No answer from the user

480

Temporarily unavailable

Subscriber absent

480

Temporarily unavailable

Call rejected

603

Decline

Number changed

410

Gone

Redirection to new destination

410

Gone

Non-selected user clearing

404

Not found

Destination out of order

502

Bad gateway

Address incomplete

484

Address incomplete

Facility rejected

501

Not implemented

Normal, unspecified

480

Temporarily unavailable

No circuit available

503

Service unavailable

Network out of order

503

Service unavailable

Temporary failure

503

Service unavailable

Switching equipment congestion

503

Service unavailable

Resource unavailable

503

Service unavailable

Содержание 4000 Media Gateway Series













































































































Результаты поиска

Содержание 4000 Media Gateway Series

Отзывы:

Похожие инструкции для 4000 Media Gateway Series

Бренды по названию

Популярные бренды

Dialogic 4000 Media Gateway Series, Справочное руководство

Результаты поиска

Содержание 4000 Media Gateway Series

Отзывы:

Похожие инструкции для 4000 Media Gateway Series

Бренды по названию

Популярные бренды