Dhollandia DH-AI02.04.01, Руководство по установке

Страница: 8 / 45

7
DHOLLANDIA
5 DESCRIPTION AND TERMINOLOGY

The DH-AI ramps are designed as a multi-purpose solution. They can be used for wheelchair access to assist wheelchair
occupants or persons with an impaired mobility embark and disembark the vehicle. And they can be used as a commercial
ramp, used to load and unload cargo.

Ramps for wheelchair access are usually finished with a mesh aluminum platform surface [option OAP821.0]. A perforated
aluminum plate with non-slip buds is available as an option OAP822.1.

As the ramps come in different versions, it is important to check the capacity of your specific ramp.

DHOLLANDIA lifts and ramps are developed and manufactured using state-of-the-art technology, high quality materials and
components, and highly skilled workmanship. They comply with the European CE safety regulations mentioned in the
Declaration of Conformity issued with each lift and ramp (unless otherwise agreed for lifts exported outside the CE region).

The DH-AI are opened and closed manually, assisted by powerful gas cylinders. DH-AI12 are equipped with 2 folding platform
sections, DH-AI13 with 3 folding platform sections.

In travel position, the ramp (DH-AI12/ 13) is stowed in upright position, just in front of the vehicle doors (standard execution), or
swung out of the way against the side of the vehicle body [option OAF820.L]. The portable ramp DH-AI02 can be stored
anywhere.
 Main details and terminology: see below.
DH-AI02/12/13
●
TERMINOLOGY
See figure below for parts corresponding to numbers in this table
# Description
1
1a Ramp frame + base plate: steel and aluminum assembly forming the feet of the ramp and connecting the ramp with the
vehicle floor. Following executions are available:
1. Standard version: ramp frame [1a] + ramp fixations [1b] designed for a fixed position of the ramp inside the vehicle
(no swing facility). The ramp frame is equipped with quick-release locks so that the ramp can be dismounted and
mounted very quickly.
2. Pivoting frame [option OAF820.L]: the ramp frame [1] incorporates an articulation pin, so that the platform can be
swung inside or outside to clear the door aperture. This ramp is not demountable.
1b Ramp fixations: fixation brackets for the ramp frame to the vehicle floor. The ramp fixations remain attached to the vehicle
floor if the ramp is dismounted (in case of standard version).
1c Quick-release locks: connects and locks the ramp frame to the ramp fixations.
2 Gas cylinders: Gas cylinders make the operation of the ramp light and easy.
3 Platform: carries the load during loading and unloading. Following surfaces are available:
[OAP821.0]
→
Platform in mesh aluminum, evacuating rainwater, snow, dirt, etc. quickly through the platform surface.
[OAP822.1]
→
Platform in perforated aluminum plate with non-slip buds.
3a Platform main section: inboard section of the foldable platform connected to the ramp frame.
3b Foldable point: foldable, outboard section of the platform resting on the ground during use.
3c Flip-over point [DH-AI13]: on DH-AI13 ramps with 3 platform sections, the foldable point [3b] is replaced by a foldable
middle section supported by support feet [7] and a flip-over point [3c] resting on the ground during use.
4 Door protection rubber: absorbs small movements and/or vibration caused by the motion of the vehicle.
5 Automatic lock: keeps the 2 (or 3) parts of the platform together in travel position.
6 Fixation pin [OAF820.L]: gives the operator the possibility to lock the platform in a 90° outwards or inwards position.
7 Support feet:
DH-AI13
→
height-adjustable feet supporting the flip-over point and middle section of the DH-AI13 while loading and
unloading.
DH-AI12.10
→
height adjustable feet proving additional support while loading and unloading heavy loads.