
16
Chapter 2
HARDWARE INSTALLATION
User's Manual |
WL9A3
DDI1_CTRLDA-
TA/DP0_AUX-
B99
I/O PCIE
AC coupled on Module PU 100K to 3.3V
(S/W IC between
Rpu/PCH)
Connect to DP AUX-
DP AUX- function if DDI1_DDC_AUX_SEL is no connect
I/O OD
CMOS
3.3V / 3.3V
PU 2.2K to 3.3V/PU
100K to 3.3V
(S/W IC between
2.2K/100K resistor)
Connect to HDMI/DVI I2C CTRLDATA
HDMI/DVI I2C CTRLDATA if DDI1_DDC_AUX_SEL is pulled high
DDI1_HPD/
DP0_HPD
B89
I CMOS
3.3V / 3.3V
PD 100K to GND
PD 1M and Connect to device Hot Plug Detect
DDI Hot-Plug Detect
DDI1_DDC_
AUX_SEL
B95
I CMOS
3.3V / 3.3V
PD 1M to GND
PU 100K to 3.3V for DDC(HDMI/DVI)
Selects the function of DDI1_CTRL and DDI1_CTRL-
DATA_AUX-. This pin shall have a 1M pull-down to logic ground on
the Module. If this input is floating the AUX pair is used for the DP
AUX+/- signals. If pulled-high the AUX pair contains the CRTLCLK
and CTRLDATA signals
************************************************************
DDI[n]_DDC_AUX_SEL shall be pulled to 3.3V on the Carrier with
a 100K Ohm resistor to configure the DDI[n]_AUX pair as the DDC
channel. Carrier DDI[n]_DDC_AUX_SEL should be connected to pin
13 of the DisplayPort
USB Signals Descriptions
Signal
Pin#
Pin Type
Pwr Rail /Tolerance
WL9A3
Carrier Board
Description
USB0+
A46
I/O USB
3.3V Suspend/3.3V
Connect 90Ω @100MHz Common Choke in series and
ESD suppressors to GND to USB connector
USB differential pairs 0
USB0-
A45
USB1+
B46
I/O USB
3.3V Suspend/3.3V
Connect 90Ω @100MHz Common Choke in series and
ESD suppressors to GND to USB connector
USB differential pairs 1
USB1-
B45
USB2+
A43
I/O USB
3.3V Suspend/3.3V
Connect 90Ω @100MHz Common Choke in series and
ESD suppressors to GND to USB connector
USB differential pairs 2
USB2-
A42
USB3+
B43
I/O USB
3.3V Suspend/3.3V
Connect 90Ω @100MHz Common Choke in series and
ESD suppressors to GND to USB connector
USB differential pairs 3
USB3-
B42
USB4+
A40
I/O USB
3.3V Suspend/3.3V
Connect 90Ω @100MHz Common Choke in series and
ESD suppressors to GND to USB connector
USB differential pairs 4
USB4-
A39
USB5+
B40
I/O USB
3.3V Suspend/3.3V
Connect 90Ω @100MHz Common Choke in series and
ESD suppressors to GND to USB connector
USB differential pairs 5
USB5-
B39
USB6+
A37
I/O USB
3.3V Suspend/3.3V
Connect 90Ω @100MHz Common Choke in series and
ESD suppressors to GND to USB connector
USB differential pairs 6
USB6-
A36
USB7+
B37
I/O USB
3.3V Suspend/3.3V
Connect 90Ω @100MHz Common Choke in series and
ESD suppressors to GND to USB connector
USB differential pairs 7
USB7-
B36
USB_0_1_OC# B44
I CMOS
3.3V Suspend/3.3V
PU 10k to 3.3VSB
Connect to Overcurrent of USB Power Switch
USB over-current sense, USB channels 0 and 1. A pull-up for this
line shall be present on the Module. An open drain driver from a
USB current monitor on the Carrier Board may drive this line low. Do
not pull this line high on the Carrier Board.