DFI LT600-DR/D/L Скачать руководство пользователя страница 8

Страница: 8 / 148

Introduction

Processor

Chipset

System Memory

Expansion Slots

Graphics

Audio

LAN

Serial ATA

• LGA 775 socket for:

- Intel

Core

2 Duo

- Intel

Pentium

- Intel

Pentium

4 or Intel

Celeron

- Intel

Celeron D

• Supports Intel Enhanced Memory 64 Technology (EMT64T)
• Supports Enhanced Intel SpeedStep Technology (EIST)
• Supports Intel Hyper-Threading Technology
• Suppor ts 1066/800/533MHz FSB (LT600-DR/D)

Suppor ts 800/533MHz FSB (LT600-L)

• Intel

chipset

- Northbridge: Intel

945G Express chipset (LT600-DR/D)

Intel

945GC Express chipset (LT600-L)

- Southbridge: Intel

ICH7R (LT600-DR)

Intel

ICH7 (LT600-D/L)

• Four 240-pin DDR2 DIMM sockets (LT600-DR/D)

Two 240-pin DDR2 DIMM sockets (LT600-L)

• Supports DDR2 533 and DDR2 667 DIMMs
• Supports dual channel (128-bit wide) memory interface
• Supports up to 4GB system memory (LT600-DR/D)

Supports up to 2GB system memory (LT600-L)

• Supports non-ECC x8 and x16 DIMMs
• Supports up to 1Gb DRAM densities
• Suppor ts unbuffered DIMMs

• 1 PCI Express x16 slot
• 6 PCI slots (LT600-DR/D)

5 PCI slots (LT600-L)

• Integrated Intel Graphics Media Accelerator 950

• Realtek ALC662 5.1-channel High Definition Audio CODEC
•

Six channel DAC support 16/20/24-bit PCM format for 5.1
channel audio solution

• Two stereo ADC suppor t 16/20-bit PCM format
• All DAC/ADC support independent 44.1k/48k/96kHz sample

rate

•

44.1k/48k/96kHz

S/PDIF-out interface

• Two Realtek RTL8111B PCI Express Gigabit controllers (LT600-DR/D)

One Realtek RTL8111B PCI Express Gigabit controller (LT600-L)

• Suppor ts 10Mbps, 100Mbps and 1Gbps data transmission
• IEEE 802.3 (10/100Mbps) and IEEE 802.3ab (1Gbps) compliant

• Supports four SATA (Serial ATA) interfaces which are compliant

with SATA 1.0 specification

• SATA speed up to 3Gb/s
• RAID 0, RAID 1, RAID 0+1 and RAID 5 (LT600-DR only)

Chapter 1 - Introduction

Specifications

Содержание LT600-DR/D/L





















































































































































Результаты поиска

Содержание LT600-DR/D/L

Отзывы:

Похожие инструкции для LT600-DR/D/L

Бренды по названию

Популярные бренды

DFI LT600-DR/D/L, Руководство пользователя

Результаты поиска

Содержание LT600-DR/D/L

Отзывы:

Похожие инструкции для LT600-DR/D/L

Бренды по названию

Популярные бренды