DFI LT600-DR/D/L Скачать руководство пользователя страница 124 | Manualshive

Страница: 124 / 148

background image

124

5

RAID

The Intel ICH7R chip alows configuring RAID on Serial ATA drives. It supports
RAID 0, RAID 1, RAID 5 and RAID 0+1.

RAID Levels

RAID 0 (Striped Disk Array without Fault Tolerance)

RAID 0 uses two new identical hard disk drives to read and write data in parallel,
interleaved stacks. Data is divided into stripes and each stripe is written alter

-

nately between two disk drives. This improves the I/O performance of the drives
at different channel; however it is not fault tolerant. A failed disk will result in
data loss in the disk array.

RAID 1 (Mirroring Disk Array with Fault Tolerance)

RAID  1  copies  and  maintains  an  identical  image  of  the  data  from  one  drive  to
the  other  drive.  If  a  drive  fails  to  function,  the  disk  array  management  software
directs all applications to the other drive since it contains a complete copy of the
drive’s  data.  This  enhances  data  protection  and  increases  fault  tolerance  to  the
entire  system.  Use  two  new  drives  or  an  existing  drive  and  a  new  drive  but  the
size of the new drive must be the same or larger than the existing drive.

RAID 5

RAID 5 stripes data and parity information across hard drives. It is fault tolerant
and provides better hard drive performance and more storage capacity.

RAID 0+1 (Mirroring and Striping)

RAID  0+1  is  a  combination  of  data  striping  and  data  mirroring  without  parity
having  to  be  calculated  and  written.  RAID  10  provides  all  the  benefits  of  both
RAID  0  and  RAID  1.  For  this  setup,  use  four  new  drives  or  use  an  existing  drive
and three new drives.

Chapter 5 - RAID (LT600-DR only)

«
...
122
123
124
125
126
...
»

Содержание LT600-DR/D/L





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для LT600-DR/D/L

Бренд: A-Trend Страницы: 40

Бренд: Yamaha Страницы: 82

Бренд: ICP Страницы: 50

Бренд: AOpen Страницы: 101

Бренд: SurfLink Страницы: 9

Бренд: ASROCK Страницы: 5

Бренд: Biostar Страницы: 45

AR0140CS2M00AUEAH3-GEVB

Бренд: ON Semiconductor Страницы: 5

Бренд: Biostar Страницы: 27

970 Extreme3 R2.0

Бренд: ASROCK Страницы: 70

Бренд: Texas Instruments Страницы: 25

JetBox 9310 Series

Бренд: Korenix Страницы: 21

Бренд: DFI Страницы: 8

Бренд: Fujitsu Siemens Computers Страницы: 42

Бренд: Gigabyte Страницы: 120

Бренд: QDI Страницы: 20

Fatal1ty Z87 Killer Series

Бренд: ASROCK Страницы: 102

Бренд: Aaeon Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды