DFI LT600-DR/D/L Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 148

background image

45

2

Hardware Installation

IDE Disk Drive Connectors

The 90

o

shrouded PCI IDE header will interface two Enhanced IDE

(Integrated Drive Electronics) disk drives. The 40-pin connector on
the IDE cable can be placed into the header only if pin 1 of the
connector is aligned with pin 1 of the header.

Connecting the IDE Disk Drive Cable

The IDE connector supports 2 devices, a Master and a Slave. Use
an IDE ribbon cable to connect the drives to the system board. An
IDE ribbon cable have 3 connectors on them, one that plugs into an
IDE connector on the system board and the other 2 connects to
IDE devices. The connector at the end of the cable is for the Master
drive and the connector in the middle of the cable is for the Slave
drive.

Install one end of the IDE cable into the IDE header on the system
board and the other connectors to the IDE devices.

X

«
...
43
44
45
46
47
...
»

Содержание LT600-DR/D/L





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для LT600-DR/D/L

Бренд: Panasonic Страницы: 26

Бренд: Intel Страницы: 80

661FX7MJ Series

Бренд: Foxconn Страницы: 81

TPS53355EVM-864

Бренд: Texas Instruments Страницы: 29

Бренд: ASROCK Страницы: 145

Бренд: Oki Страницы: 24

Бренд: ASROCK Страницы: 2

Бренд: NXP Semiconductors Страницы: 12

Бренд: JETWAY Страницы: 52

Бренд: Renesas Страницы: 17

Бренд: ITOX Страницы: 114

Бренд: Supermicro Страницы: 105

Бренд: Biostar Страницы: 68

Бренд: Gigabyte Страницы: 96

Бренд: JGINYUE Страницы: 14

Бренд: Yamaha Страницы: 124

Бренд: Yamaha Страницы: 126

Бренд: Yamaha Страницы: 124

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды