DFI LT600-DR/D/L Скачать руководство пользователя страница 114 | Manualshive

Страница: 114 / 148

background image

114

4

Supported Software

Hardware Monitor for Windows
(for Windows 7 / Windows Vista)

The  Hardware  Monitor  for  Windows  utility  is  capable  of  monitoring  the  system’s
temperature,  fan  speed,  voltage,  etc.  and  allows  you  to  manually  set  a  range
(Highest  and  Lowest  Limit)  to  the  items  being  monitored.  If  the  settings/values
are  over  or  under  the  set  range,  a  warning  message  will  pop-up.  The  utility  can

also be configured so that a beeping alarm will sound whenever an error occurs.

We recommend that you use the “Default Setting” which is the ideal setting that
would keep the system in good working condition.

To install the utility, click “Hardware Monitor for Windows” on the main menu.

1. Setup is now ready to in-

stall the utility. Click Next.

2. Click Next to install or click

Browse to select another
folder.

«
...
112
113
114
115
116
...
»

Содержание LT600-DR/D/L





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для LT600-DR/D/L

Бренд: ST Страницы: 77

A320M-K PRO V14

Бренд: Colorful Страницы: 12

Бренд: MSI Страницы: 22

Бренд: MINATO Страницы: 125

Бренд: Maxim Страницы: 7

Бренд: TYAN Страницы: 100

KXTJ3-1057-EVK-001

Бренд: Rohm Страницы: 3

Бренд: Gigabyte Страницы: 34

Бренд: JETWAY Страницы: 48

Бренд: IEI Technology Страницы: 12

BOOSTXL-DRV8301

Бренд: Texas Instruments Страницы: 13

Бренд: MSI Страницы: 180

Бренд: J&W Страницы: 36

Memorator Pro 2xHS v2 CB

Бренд: Kvaser Страницы: 22

NF4 SLI INFINITY

Бренд: DFI Страницы: 127

Бренд: DFI Страницы: 69

Бренд: DFI Страницы: 37

Бренд: Asus Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды