DFI 586ITBD Скачать руководство пользователя

Страница: 53 / 89

Award BIOS Setup Utility

CPU Internal Cache and External Cache

These categories speed up the memory access. The default value

is enabled. Enable the External Cache for better performance.

Quick Power On Self Test

This category speeds up Power On Self Test (POST) after you

power on your system. When Enabled, the BIOS will shorten or

skip some check items during POST.

Boot Sequence

This category determines which drive to search first for the disk

operating system (i.e. DOS). The default is A, C, SCSI.

The options are:

A, C, SCSI;

C, A, SCSI;

C, CDROM, A;

CDROM, C, A;

D, A, SCSI;

E, A, SCSI;

F, A, SCSI;

SCSI, A, C;

SCSI, C, A;

C only;

LS120/ZIP, C.

Swap Floppy Drive

When this option is enabled and the system is booting from the floppy

drive, the system will boot from drive B instead of drive A. When this

option is disabled and the system is booting from the floppy drive, the

system will boot from drive A. You must have two floppy drives to

use this function.

Boot Up Floppy Seek

When enabled, the BIOS will check whether the floppy disk drive

installed is 40 or 80 tracks. Note that the BIOS cannot distinguish

between 720K, 1.2M, 1.44M and 2.88M drive types as they are all

80 tracks. When disabled, the BIOS will not search for the type of

floppy disk drive by track number. Note that there will not be any

warning message if the drive installed is 360KB.

Boot Up NumLock Status

This allows you to determine the default state of the numeric

keypad. By default, the system boots up with NumLock on wherein

the function of the numeric keypad is the number keys. When set

to Off, the function of the numeric keypad is the arrow keys.

Содержание 586ITBD


























































































Результаты поиска

Содержание 586ITBD

Отзывы:

Похожие инструкции для 586ITBD

Бренды по названию

Популярные бренды

DFI 586ITBD, Руководство пользователя

Результаты поиска

Содержание 586ITBD

Отзывы:

Похожие инструкции для 586ITBD

Бренды по названию

Популярные бренды