DFI 586ITBD Скачать руководство пользователя

Страница: 7 / 89

Introduction

Features and Specifications

Processor Upgrade

The system board is equipped with a 321-pin ZIF socket (Intel



Socket 7). This socket is designed for easy removal of an old

processor and easy insertion of an upgrade processor. The system

board is also equipped with a switching voltage regulator that

supports 2.0V, 2.2V, 2.8V, 2.9V, 3.2V, 3.3V and 3.5V core voltage for

various processors.

Intel Pentium



processor with MMX

technology-166/200/

233MHz

Intel Pentium



90/100/120/133/150/166/200MHz

Cyrix



6x86L PR150+/PR166+ and 6x86MX-PR166/PR200/

PR233, M II-300

AMD



K5 PR90/PR100/PR120/PR133/PR166

AMD



K6-166, K6-200, K6-233, K6-266, K6-300 and K6-2/266

Chipset

Intel



82430TX PCIset chipset

System Memory

The system board supports 8MB to 256MB of memory. It is

equipped with two DIMM and four SIMM sockets. The 168-pin

DIMM sockets use x64 EDO (60/70ns), fast page mode (60/

70ns), or SDRAM (10/12/13ns), 3.3V. The 72-pin SIMM sockets

use EDO or fast page mode, 60/70ns, x32 DRAM, 5V.

Cache Memory

512KB pipeline burst, direct map write-back cache installed on

the system board.

BIOS

Award BIOS, Windows



95 Plug and Play compatible

Flash EPROM for easy BIOS upgrades

Supports DMI function

Содержание 586ITBD


























































































Результаты поиска

Содержание 586ITBD

Отзывы:

Похожие инструкции для 586ITBD

Бренды по названию

Популярные бренды

DFI 586ITBD, Руководство пользователя

Результаты поиска

Содержание 586ITBD

Отзывы:

Похожие инструкции для 586ITBD

Бренды по названию

Популярные бренды