DFI 586ITBD Скачать руководство пользователя

Страница: 43 / 89

Hardware Installation

Power Supply Connectors

The system board is a Baby AT form factor system board

designed to fit into an ATX form factor chassis. The board is

equipped with both ATX (J11) and AT (J1) power supply

connectors. Power-Supply Type in the Chipset Features Setup

must be set according to the type of power supply installed in

your computer. The default is AT (for an AT power supply). If you

are using an ATX power supply, make sure to set this field to ATX.

Refer to Chapter 3 - Chipset Features Setup for more

information.

Using an ATX power supply, you can either shut down your com-

puter by pressing the Power button located on the front bezel of

your computer or by executing the Shut Down command under

the Windows



95 operating system. Your system will then enter

the Soft Off state. To power-on your system automatically, enable

Resume By Alarm in the Power Management Setup of the

Award BIOS. This will allow you to set the day and time you

would like your system to power-on. Refer to Chapter 3 - Power

Management Setup for more information. Install the 20-pin ATX

power cable connector into location J11 on the system board. The

20-pin connector can be inserted into J11 only if pin 1 of the

connector is aligned with pin 1 of J11.

(ATX)

Refer to the table on the next page for the pin assignments of the

ATX power connector.

Содержание 586ITBD


























































































Результаты поиска

Содержание 586ITBD

Отзывы:

Похожие инструкции для 586ITBD

Бренды по названию

Популярные бренды

DFI 586ITBD, Руководство пользователя

Результаты поиска

Содержание 586ITBD

Отзывы:

Похожие инструкции для 586ITBD

Бренды по названию

Популярные бренды