DFI 586ITBD Скачать руководство пользователя

Страница: 8 / 89

586ITBD System Board Users Manual

Energy Efficient Design

System power management supported

CPU stopped clock control

Hardware supports SMI green mode

Microsoft

/Intel

APM 1.2 compliant

Soft Power supported - ACPI v1.0a specification (ATX power

supply only)

ACPI Specification and OS Directed Power

Management (ATX power supply only)

The system board is designed to meet the ACPI (Advanced

Configuration Power Interface) specification. It has energy saving

features which enable operating systems to reliably manage and

coordinate power planes, PnP (Plug-and-Play) peripherals, and

cooling fans. The system board is PC 97 compliant. Microsoft



PC 97 "OnNow" design allows continual "power on" with reduced

energy consumption.

RTC Timer to Power-on the System

The RTC installed on the system board allows your system to

automatically power-on on the set day and time. Set the day and

time you would like your system to power-on in the Resume By

Alarm field (Power Management Setup) of the Award BIOS.

Modem Wake-up/Ring-on

The Modem Wake-Up feature allows the sleeping (Suspend

mode) PC to wake-up to respond to incoming calls. The Modem

Ring-on feature allows the Soft Power Down (Soft-Off) PC to

power-on to respond to incoming calls. Enable this function in the

Resume By Ring field and select an IRQ channel for the external

modem in the Modem Use IRQ field (Power Management

Setup). Make sure to set JP2 to the COM port where your

modem is connected.

Note:

This feature supports external modem only.

Содержание 586ITBD


























































































Результаты поиска

Содержание 586ITBD

Отзывы:

Похожие инструкции для 586ITBD

Бренды по названию

Популярные бренды

DFI 586ITBD, Руководство пользователя

Результаты поиска

Содержание 586ITBD

Отзывы:

Похожие инструкции для 586ITBD

Бренды по названию

Популярные бренды