Deye SUN-10.5K-G Скачать руководство пользователя страница 41

Страница: 41 / 47

9. Repair and Maintenance

10.Error informa�on and processing

- 39 -

10.1 Error code

String type inverter doesn’t need regular maintenance. However,debris or dust will aﬀect heat

sink’s thermal performance. It is be�er to clean it with a so� brush. If the surface is too dirty

and aﬀect the reading of LCD and LED lamp, you can use wet cloth to clean it up.

Inverter has been designed in accordance with interna�onal grid �ed standards for safety,

and electromagne�c compa�bility requirements. Before delivering to the customer the

inverter has been subjected to several tests to ensure its op�mal opera�on and reliability.

If there is any failure,the LCD screen will display an alarm message. In this case,the inverter

may stop feeding energy into the grid. The alarm descrip�on and their corresponding alarm

messages are listed Table 10.1

Warning:

When the device is running, the local temperature is too high and the touch can

cause burns. Turn oﬀ the inverter and wait for it cooling, then you can clean and

maintain.

Warning:

No solvent, abrasive materials or corrosive materials can be used for cleaning

any parts of the inverter.

Error code

Description

Ongrid - Single Phase

F01

DC input polarity reverse fault

Check the PV input polarity

F03

DC leakage current fault

Hardly appear the code. Never ever happened so far

F07

GFDI blown fuse

Hardly appear the code. Never ever happened so far

F08

GFDI grounding touch failure

Hardly appear the code. Never ever happened so far

F02

DC insula�on impedance

permanent fault

Check the grounding cable of inverter.

F04

Ground fault GFDI

Check the solar panel output connec�on.

F09

IGBT damaged by excessive drop

voltage

Hardly appear the code. Never ever happened so far.

F05

Read the memory error

Failure in reading memory (EEPROM). Restart the inverter if the

fault s�ll exists, contact your installer or Deye service.

F06

Write the memory error

Failure in wri�ng memory (EEPROM). Restart the inverter if the

fault s�ll exists, contact your installer or Deye service.

Содержание SUN-10.5K-G
















































Результаты поиска

Содержание SUN-10.5K-G

Отзывы:

Похожие инструкции для SUN-10.5K-G

Бренды по названию

Популярные бренды

Deye SUN-10.5K-G, Руководство пользователя

Результаты поиска

Содержание SUN-10.5K-G

Отзывы:

Похожие инструкции для SUN-10.5K-G

Бренды по названию

Популярные бренды