Model
P2201
Cat. No.
DDF211022P
P2201
5
.300 head Diameter Drive Pins with 1-7/8” insulation Washer
CaT.
Shank
STD.
STD.
heaD
Shank WT./
no.
lengTh Box CTn.
Dia.
Dia.
100
DDf3081000 1-1/2”
100 1000 .300
.143 2.1
DDf3081050 2-1/2”
50
500 .300
.143 2.7
1/4”-20 Threaded Studs
CaT. ThReaD Shank STD.
STD.
heaD Shank WT./
no. lengTh lengTh Box
CTn.
Dia.
Dia.
100
DDf3811020 1/2” 1/2”k 100 5000 1/4” .143 .8
DDf3811000 3/4” 1/2”k 100
1000
1/4”
.143
1.1
DDf3811050 3/4” 3/4” 100
1000
1/4”
.143
1.2
DDf3811100 1/2” 1” 100
1000
1/4”
.143
1.2
DDf3811150 3/4” 1” 100
1000
1/4”
.143
1.4
DDf3811180 1/2” 1-1/4” 100
1000
1/4”
.143
1.4
DDf3811200 3/4” 1-1/4” 100
1000
1/4”
.143
1.5
DDf3811250 1-1/4” 1-1/4” 100 1000 1/4” .143 1.7
.300 head Diameter Pins with Ceiling Clips
CaT.
Shank
STD. STD. heaD Shank
WiRe
WT./
no.
lengTh Box CTn. Dia.
Dia.
hole
100
DDf4111050 1”
100 1000 .300
.143
0.278” 3.5
DDf4151000 1”
100 1000 .300
.143
0.278” 3.0
DDf4111100 1-1/4”
100 1000 .300
.143
0.278” 3.7
DDf4111150 1-1/4”
100 1000 .300
.143
0.278” 3.2
.300 head Diameter Drive Pins with
Bx Cable Straps and Conduit Clips
CaT.
STD.
STD.
heaD Shank WT./
no.
Shank lengTh Box
CTn.
Dia.
Dia.
100
DDf4111150 1”
100 1000 .300 .143 3.5
DDf4131050 1-1/4”
100 1000 .300 .143 3.7
DDf4121000 1/2” EMT 1” pin 100
1000
.300
.143
3.3
DDf4121050 3/4” EMT 1-1/4”pin 100 1000 .300 .143 3.5
DDf4121100 3/4” EMT 1” pin TH 100 500 .300 .143 3.4
DDf4121150 3/4” EMT 1” pin 100
1000
.300
.143
3.3
DDf4121200 1” EMT 1” pin TH 25 250 .300 143 3.2
k=knurled TH=Top Hat
.300 head Diameter Pins with Rebar Basket Clip
CaT.
STD. STD.
heaD Shank WT./
no.
DeSCRiPTion Box CTn.
Dia.
Dia.
100
DDf4251000 32mm w/ basket clip 100 100
8mm
.143
4.0
DDf4251050 37mm w/ basket clip 100 100
8mm
.143
4.1
DDf4251150 37mm w/ basket clip 100 100
8mm
.143
4.4
DDf4252000 37mm w/ basket clip 100 100
8mm
.143
4.6
DDf4252500 37mm w/ basket clip 100 100
8mm
.143
4.8
Forming Pins
CaT.
STD.
STD.
heaD Shank WT./
no.
DeSCRiPTion Box CTn.
Dia.
Dia. 100
DDf3951050 62mm - 2-1/2” 100
1000
.205
.143
1.4
DDf3951000 44mm - 1-5/8” 100
1000
.205
.143
1.2
Powder Load Selection Guide
CaT. PoWeR loaD STD.
STD.
MaSTeR
WT./
no. level ColoR Size
Box
CTn.
CTn.
100
DDf1111100 1 Grey .22A
100
1000
20000
.33
DDf1111200 2 brown .22A
100
1000
20000
.33
DDf1111300 3 Green .22A
100
1000
20000
.33
DDf1111400 4 Yellow .22A
100
1000
20000
.33
fety InstructIons
safety InstructIons
Safety is your primary responsibility when operating
any powder actuated tool. You must read and understand
the contents of this manual. You must be familiar with all
functional and safety requirements of the tool. It is your
responsibility to obtain proper training and a D
E
wALT operator
card prior to using this tool in compliance with the current
American National Standard A10.3 Safety Requirements
for Powder Actuated fastening Systems and the federal
Occupational Safety and Health Administration Standards
(OSHA). Existing state or local regulations should also be
followed. when using this tool, you must have the qualified
operators card in your possession.
Revocation of card - failure to comply with any of the rules and
regulations for safe operation of powder actuated tools shall be
cause for the immediate revocation of your qualified operator card.
Failure to following safety instructions
can result in serious injury or death to operators or
bystanders.
Prior to operating the Tool
1. warning signs should always be posted within the area in
which a powder actuated tool is to be used. These signs
should be at least 8” x 10” in size with boldface type that
is not less than 1” in height. The sign should state
“Powder Actuated Tool In Use”.
2. Approved eye protection should always be worn by opera-
tor or bystander, to protect their eyes from flying particles.
Hearing protection should always be worn by the operator
and bystanders when using a powder actuated tool. Other
personal safety protection as required should also be used.
3. Never modify or fabricate parts for use in your D
E
wALT
tool. Use only D
E
wALT fasteners, loads, and tool parts.
4. Hands or other body parts must never be placed in front
of muzzle/barrel. Accidental discharge can cause piston
and/or fastener to pass through the operator’s hand.
5. Never compress the tool against any part of the body.
Serious injury or death may result in the event of an
accidental discharge.
6. Always point tool in a safe direction at all times.
intended Purpose
7. keep all other people, especially children, away from the
work area.
8. Use only in a well-lit, well-ventilated work area.
Preparation for loading the Tool
1. Tools must be checked prior to operating to make sure
they are not fully or partially loaded with a powder load or
fastener.
2. To insure safe operation, perform the daily function test
described in this manual. be sure the tool is not loaded
prior to performing this test.
3. Do not operate this tool unless all its parts are in place
and operating appropriately. Never attempt to use a
malfunctioning tool. Call
1-800-4-DeWalT
for assistance.
4. Never guess about the suitability of a base material. If
you are uncertain about the suitability of a base material,
perform a center punch test.
5. Do not operate the tool until you learn and understand the
color code / numbering system used to identify the power
level of powder loads.
operating the Tool
1. Only use fasteners and powder loads designed for this
tool as supplied by D
E
wALT.
2. Do not use powder actuated tools in the presence of
flammable fumes or vapor or an explosive atmosphere.
3. Do not fire a tool without a fastener. The piston will
POW2273_manual_P2201_dewalt.indd 5
3/10/14 12:41 PM
Содержание P2201
Страница 30: ...P2201 Model P2201 Modelo P2201 ModÈlE P2201 30 POW2273_manual_P2201_dewalt indd 30 3 10 14 12 41 PM ...
Страница 31: ...P2201 Model P2201 Modelo P2201 ModÈlE P2201 31 POW2273_manual_P2201_dewalt indd 31 3 10 14 12 41 PM ...
Страница 32: ...P2201 Model P2201 Modelo P2201 ModÈlE P2201 32 POW2273_manual_P2201_dewalt indd 32 3 10 14 12 41 PM ...