DeWalt DCF622NT, Оригинальное руководство пользователя

Страница: 13 / 28

11
English
D
Cleaning
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non‑metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
C
Lubrication
Your power tool requires no additional lubrication.
MAINTENANCE
Your power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories.
An accidental
start‑up can cause injury.
The charger and battery pack are not serviceable.
2. If after pushing the screw into the work piece there is no
chuck rotation, check the adjustment range on the collar
marked MAX/MIN
4 . Rotate the collar to increase the
clutch engagement.
3. Test drive a fastener into a scrap piece to check proper
fastener seating. It is normal after a period of use to
require a slightly different collar setting due to wear on the
clutch faces.
nOTE: With Versa Clutch™, the operator has the ability to
“override” clutch ratchet if a fastener hits a wood knot, variable
hardness in steel work pieces or incorrect pilot holes. Increased
operator pressure will usually cause the clutches to pick‑up
and continue to seat the fastener. Further, a quick twist of the
collar will change the clutch setting to overcome most driving
difficulties and will provide for immediate change in torque
output giving the operator the option to drive a wide range of
fastener sizes.
Proper hand position requires one hand on the rear grip or main
handle. Take care to not block the air vents
15
.
Quick‑Change Chuck (Fig. A, F)
nOTE: The chuck accepts 6.35 mm hex accessories.
Place the forward/reverse control lever
6
in the lock‑off (centre)
position and remove battery pack before changing accessories.
To install an accessory, pull the quick‑change sleeve
2
away
from the front of the tool then fully insert the accessory into
the quick‑change chuck
1 . When the sleeve is released, the
accessory is locked into place (Fig. F).
To remove an accessory , pull the quick‑change sleeve 2
away from the front of the tool, then remove the accessory from
the quick‑release chuck
1 (Fig. F).
Versa Clutch™ (Fig. G)
This tool features the Versa Clutch™ which allows a wide range
of fastener sizes. To adjust:
1. Pull forward, then rotate clutch collar 5 in the "Increase"
direction as indicated on adjustment collar 3 , to increase
the amount of clutch engagement and torque output.
Maximum rotation of the collar in the "Increase" direction
results in full clutch engagement and maximum torque
output and fastener capacity. The collar and adjustable stop
will not screw off the clutch housing.
Proper Hand Position (Fig. C)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories.
An accidental
start‑up can cause injury.
WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the belt hook
is secure.
iMPORTAnT: When attaching or replacing the belt hook
12
,
use only the screw that is provided. Be sure to securely tighten
the screw.
The belt hook
12 can be be attached to either side of the tool
using only the screw provided, to accommodate left‑ or right‑
handed users. If the hook is not desired at all, it can be removed
from the tool.
To move belt hook, remove the screw that holds it in place then
reassemble on the opposite side. Be sure to securely tighten
the screw.