DeWalt D21620, Оригинальное руководство пользователя

Страница: 29 / 132

ENGLISH
27
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in
the plug.
• Connect the blue lead to the neutral terminal.
• Connect green / yellow lead to the earth
terminal.
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved
3-core extension cable suitable for the power
input of this tool (see technical data).The minimum
conductor size is 1.5 mm
2 ; the maximum length is
30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing
set- ups or when making repairs.
Be
sure the switch is in the OFF position.
An accidental start-up can cause injury.
Installing the Machine (fi g. 2–5)
1. Assemble the feed handle.
2. Mount the drill guard.
3. Fit the lubrication system as necessary.
4. Place the machine on a clean, level and solid
surface. Remove any particles that will obstruct
full contact between the magnetic stand and
the mounting surface.
5. Fit and tighten the safety strap.
ASSEMBLING THE FEED HANDLE (FIG. 1, 2)
The quick-release feed handle (e) can be mounted in
one simple operation both to the left and the right of
the machine.
1. Screw the handles (i) into the hub (j).
2. Keep the button (k) depressed while inserting
the hub shaft into the hole (l).
3. Release the button.
MOUNTING THE DRILL GUARD (FIG. 3)
1. Hold the guard (g) in front of the tool holder,
aligning the slots in the guard with the holes in
the machine.
2. Fit the screw (m) into the hole (n) located in the
front of the frame.
3. Fit a knob (o) into each of the holes (p) located
at both sides of the frame.
4. Do not tighten the fasteners firmly as the
drill guard must be able to rise and lower as
required.
WARNING: Always use the drill guard.
FITTING THE LUBRICATION SYSTEM (FIG. 4)
The lubrication system can be used for horizontal
drilling applications (the drill being used vertically).
1. Loosen the knob (q) and turn the bracket (r) in
position. Tighten the knob.
2. Hold the cutting fluid tank (h) against the
bracket and push it in its place.
3. Place the hose (t) between the cutting fluid tank
(h) and the connection in the frame (u).
In order to use the lubrication system, it must be
filled with a sufficient amount of cutting fluid.
1. Make sure the flow regulator (v) is closed.
2. Unscrew the cap (w).
3. Fill the container with cutting coolant diluted
with water.
4. Screw the cap back on.
WARNING: Do not use the lubrication
system in vertical or overhead drilling
applications.
FITTING THE SAFETY STRAP (FIG. 5)
1. Pass the safety strap (x) through the slot (y).
2. Wrap the strap around the workpiece as shown.
3. Securely tighten the strap using the buckle (z).
WARNING: Always use the safety
strap.
Inserting and Removing an
Accessory (fi g. 6)
The tool holder accepts annular cutters with a
19 mm shank with one or more flats.
WARNING: The teeth of a cutter are
very sharp and can be dangerous.
1. In order to fit an accessory it is necessary to
raise the the guard (g) to its highest position.