Dettson AMP1-IE2 Скачать руководство пользователя страница 36

 

5

WARNING

 

Do Not block the combustion air openings in 
the furnace.  Any blockage will result in 
improper combustion and may result in a fire 
hazard and/or cause bodily harm. 

 
 

Chimney installation only 

 
The barometric draft regulator, included with the 
furnace, shall be installed in the same room or 
enclosure as the furnace in such a manner as to 
prevent any difference in  pressure between the 
regulator and the combustion air supply. 
 
Air requirements for the operation of exhaust fans, 
kitchen ventilation systems, clothe dryers, and 
fireplaces shall be considered in determining the 
adequacy of a space to provide combustion air 
requirements. 
 
In unconfined spaces, in buildings of conventional 
frame, brick or stone construction infiltration may be 
adequate to provide air for combustion, ventilation 
and dilution of flue gases.  This determination must be 
made on an individual installation basis and must take 
into consideration the overall volume of the 
unconfined space, the number of windows and 
ventilation openings, the number of doors to the 
outside, internal doors which can close off the 
unconfined space and the overall tightness of the 
building construction. 
 
Many new buildings and homes (and older ones that 
have been weatherized must be considered as being 
tight construction an, therefore, infiltration will not be 
sufficient to supply the necessary air for combustion 
and ventilation to supply the necessary air for 
combustion and ventilation. 
 
A building can be considered as being of tight 
construction when: 
 
a.  Walls and ceilings exposed to the outside 

atmosphere have a continuous water vapor 
retarded with a rating of one perm or less with 
openings gaskets or sealed and/or 

b.  Weather-stripping has been added on operable 

windows and doors, and/or 

c.  Caulking or sealant are applied to areas such as 

joints around window and door frames, between 
sole plates and floors, between wall-ceiling  joints, 
between wall panels, at penetrations for plumbing, 
electrical and fuel lines and at other openings. 

 

 
 
 
 
 

2.2)  Duct recommendations:

  

 
The proper sizing of warm air ducts is necessary to 
insure satisfactory furnace operation.  Ductwork 
should be in accordance with the latest editions of 
NFPA-90A (Installation of Air Conditioning and 
Ventilating Systems) and NFPA-90B (Warm Air 
Heating and Air Conditioning Systems) or Canadian 
equivalent. 
 
The supply ductwork should be attached to the flanged 
opening provided at the discharge end of the furnace.  
See figures # 5.1 and # 5.2 for the dimensions of this 
opening. 
 
Knockouts are provided on both sides of the furnace 
to cut the required size opening for the installation of 
the return ductwork.  This can be done on either the 
right or the left side of the furnace.  See table # 2 for 
location and dimensions. 
 
 

NOTE:

  THE BACK SHOULD NOT BE CUT OUT 

FOR RETURN AIR 

 
 
Provision is also made on this furnace for a bottom 
return air duct. Knockouts are provided on the floor of 
the furnace to facilitate the cut out requirement to 
assembly of air filter rack and return ductwork. (We 
recommend the use of this opening for horizontal and 
counterflow installations). 
 
The following recommendations should be followed 
when installing ductwork: 
 
a.  Install locking type dampers in all branches of the 

individual ducts to balance out the system.  
Dampers should be adjusted to impose the proper 
static pressure at the outlet of the furnace. 

b.  A flexible duct connector of noncombustible 

material should be installed at the unit on both the 
supply and return air systems.  In applications 
where extremely quiet operation is necessary, the 
first 10 feet (if possible) of supply and return ducts 
should be internally lined with acoustical material. 

c.  In cases where the return air grille is located close 

to the fan inlet, there should be at least one 90

o

 air 

turn between fan inlet and grille. Further reduction 
in sound level can be accomplished by installing 
acoustical air turning vanes or lining duct as 
described in item 2 above. 

d.  When a single air grille is used, the duct between 

grille and furnace must be the same size as return 
opening in furnace. 

 

CAUTION 

Return air grilles and warm air registers must 
not be obstructed. 

 

Содержание AMP1-IE2































































Отзывы: