Detex ADVANTEX 70 Series Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 20

Detex ADVANTEX 70 Series Скачать руководство пользователя страница 15

REFER TO TRIM INSTRUCTIONS AT THIS TIME, IF APPLICABLE

INSTALL DOOR ONTO FRAME PER MANUFACTURER'S SPECIFICATIONS

11c

11a

Right Hand Reverse

(RHR)

If link is not in uppermost position on the centerlift,

carefully remove "E" clips and reposition link on
top pin of the centerlift and replace "E" clips.
Verify carriage moves up and down smoothly when
pushpad is depressed and released.

Rehanding procedure

if required

HANDING INDICATOR

ON CENTERLIFT

Left Hand Reverse

(LHR)

MOVE LIFT PIN & SETSCREW TO

BOTTOM POSITION ON CARRIAGE.

11b

LIFT PIN

MUST

BE ON

BOTTOM

Remove setscrew then liftpin which

screws out of the back.

NOTE: LINK MUST ALWAYS

BE IN TOP POSITION

setscrew

liftpin

L

2

Check for device and door frame clearance.

If no cut-off needed, proceed to the next page.

CUT

fillerplate and extrusion straight &

square to desired length and deburr.

SECURE

with tape before cutting

Minimum

Fillerplate

Length

SLIDE

endcap

assembly
onto
extrusion

CAUTION:

CHECKING FOR DEVICE CLEARANCE

(Cut-Off procedure if required)

Type

Length (L)

2-1/2"

LD

3"

HD/CD

For aluminum Advantex finish cutdown applications:

After cutting, the baseplate extrusion can be reversed to place
the cut end inside the head cover. To do so, loosen the
setscrew inside the aluminum baseplate extrusion and slide
extrusion out, reverse, & slide back in. Tighten setscrew.

11f

104948 Page 15

COMPLETE BACKPLATE MOUNTING

REFER TO TRIM INSTRUCTIONS AT THIS TIME, IF APPLICABLE

INSTALL DEVICE TO BACKPLATE

Lift pin protruding from back of centercase

MUST

be inserted

BETWEEN

these two tabs.

Door OPEN position,
latches RETRACTED

Install device to backplate & fasten with 2 screws.
Depress pushpad appropriate amount to line up

lift pin with tabs.

STEP 11:

HANG DOOR / ASSEMBLE DEVICE TO DOOR

Drill 3/16 pilot hole x 1" deep

11d

11e

11c

1

OR

Drill exterior door face 1/2" (With Trim)

or 3/8" (Without Trim).

Drill interior door face 9/32".

and

Install 4 screws or sexnuts and lockwashers

«
...
13
14
15
16
17
...
»

Содержание ADVANTEX 70 Series





















Отзывы:

Нет отзывов