Desoutter Delta Wrench 150 Nm Скачать руководство пользователя страница 45

Страница: 45 / 184

Part Number
Issue
Date
Page

6159937790
12
03/2018
45 / 184

45 (184)

03/2018

The

areas

shown in the main menu (refer to the above picture) can be customized; select

View

define which areas enable or disable:

The

areas

listed in “

View

”

are as follow:

Build area

Enable/disable the

Build

area. It contains the commands to create tightening

and test programs, tools, route of test.

Tree

Enable/disable the

Assembly line

area. It contains the list of the tightening

programs and tools created in

Online / Offline mode

Details

Enable/disable the

Assembly line

details

area. It details the items selected in

the

Assembly line

area.

Log area

Enable/disable the

Log

area that lists the list of the log messages.

All

Enable/disable all the possible items in the main menu.

Restore default
layout

Restore the default layout that enables all the items except the

Log

area.

To hide one

area

directly from the main menu, click on the

icon (refer to the picture below):

Содержание Delta Wrench 150 Nm

























































































































































































Результаты поиска

Содержание Delta Wrench 150 Nm

Отзывы:

Desoutter Delta Wrench 150 Nm, Руководство пользователя, Страница: 45 / 184

Результаты поиска

Содержание Delta Wrench 150 Nm

Отзывы: