Desoutter Delta Wrench 150 Nm Скачать руководство пользователя страница 20

Страница: 20 / 184

Part Number
Issue
Date
Page

6159937790
12
03/2018
20 / 184

03/2018

20 (184)

3.2

Keyboard

Use the keyboard to browse the Delta Wrench menu:

3.3

Buzzer

The Delta Wrench features a buzzer, to provide more indications on the result of the current
operation. A high tone is emitted in case of

result, while a lower tone is emitted in case of test

Not

. For further details, refer to the specific paragraphs related to the various tests available on the

Delta Wrench.

3.4

Mini USB Port

The mini USB port is available for programming the Delta Wrench with DeltaQC software.
For further details, refer to the paragraph “

Connecting to the Delta Wrench

”.

It is used also for firmware upgrade (reserved for authorized Desoutter Service Personnel).

Icon

Name

Description

ON,

ENTER

Switch on the Delta Wrench, enter menu and
confirm.

OFF, ESC Switch off the Delta Wrench, exit menu.

Up (browse menu), increase value in settings
menus.

DOWN

Down (browse menu), decrease value in
settings menus.

Mini USB port

Содержание Delta Wrench 150 Nm

























































































































































































Результаты поиска

Содержание Delta Wrench 150 Nm

Отзывы:

Desoutter Delta Wrench 150 Nm, Руководство пользователя, Страница: 20 / 184

Результаты поиска

Содержание Delta Wrench 150 Nm

Отзывы: