Desoutter Delta Wrench 150 Nm Скачать руководство пользователя страница 143

Страница: 143 / 184

Part Number
Issue
Date
Page

6159937790
12
03/2018
143 / 184

143 (184)

03/2018

The

Main Toolbar

(refer to the above screen) allows the user to customize the

Results Viewer

page

Furthermore, it provides important data.

The “

Filters drop-down menu

” (refer to the above screen), filters the results according to customer

needs. It is possible to display the results after selecting among the following options:

No Filter

Status OK

Status KO

Torque status OK

Torque status KO

Angle status OK

Angle status KO

The “

Pset Filter

” button (refer to the above screen), allows the user to filter the results according to the

test that made them.
After clicking on “

Pset Filter

” button, the following pop-up is shown:

Select the test to be reviewed and click on

The “

Progress bar

” and the “

Results found

” options provide important data related to the results.

The “

Progress bar

” (refer to the above screen) is a graphical control element used to visualize the

progression of the results downloaded: when it is totally green, all the results are downloaded.

The “

Results found

” option (refer to the above screen) indicates the number of results either

performed (

Online

mode) or stored into the database (

Offline

mode).

The “

Delete

” button (refer to the above screen) discards the selected item(s).

NOTE

: The “

Delete

” button is available ONLY working in

Offline

mode.

Search / filter

functions

Select manually

the tests

Select/deselect

all the tests

Содержание Delta Wrench 150 Nm

























































































































































































Результаты поиска

Содержание Delta Wrench 150 Nm

Отзывы:

Desoutter Delta Wrench 150 Nm, Руководство пользователя, Страница: 143 / 184

Результаты поиска

Содержание Delta Wrench 150 Nm

Отзывы: