Desa VsGF28nTF Скачать руководство пользователя

Страница: 23 / 32

www.desatech.com

119303-01A

TroUbleshooTinG

Continued

POSSIBLE CAUSE

1. Control knob not fully pressed in

2. Control knob not pressed in

long enough

3. Equipment shutoff valve not

fully open

4. Pilot flame not touching ther

mocouple, which allows ther

mocouple to cool, causing

pilot flame to go out. This

problem could be caused by

one or both of the following:

A) Low gas pressure

B) Dirty or partially clogged

ODS/pilot

5. Thermocouple connection

loose at control valve

6. Thermocouple damaged

7. Control valve damaged

8. Safety interlock system has

been triggered

1. Inlet gas pressure is too low

2. Burner orifice(s) clogged

3. Mislocated crossover tube

1. Manifold pressure is too low

2. Burner orifice(s) clogged

3. Mislocated crossover tube

1. Burner orifice is clogged or

damaged

2. Damaged burner

3. Gas regulator defective

1. Not enough air

2. Gas regulator defective

REMEDY

1. Press in control knob fully

2. After ODS/pilot lights, keep

control knob pressed in 30

seconds

3. Fully open equipment shutoff

valve

4. A) Contact local natural or

propane/LP gas company

B) Clean ODS/pilot (see

Cleaning and Maintenance

page 20) or replace ODS/pilot

assembly

5. Hand tighten until snug, then

tighten 1/4 turn more

6. Replace pilot assembly

7. Replace control valve

8. Wait one minute for safety in

terlock system to reset. Repeat

ignition operation.

1. Contact local natural or pro

pane/LP gas company

2. Clean burner(s) (see C

leaning

and Maintenance

, page 20)

or replace burner orifice(s)

3. Contact qualified service

person

1. Contact local natural or pro

pane/LP gas company

2. Clean burner(s) (see

Cleaning

and Maintenance

, page 25) or

replace burner orifice(s)

3. Contact qualified service person

1. Clean burner (see

Cleaning

and Maintenance

, page 20)

or replace burner orifice(s)

2. Replace damaged burner

3. Replace gas regulator

1. Check burner(s) for dirt

and debris. If found, clean

burner(s) (see

Cleaning and

Maintenance

, page 20)

2. Replace gas regulator

OBSERVED PROBLEM

ODS/pilot lights but flame

goes out when control knob is

released

One or both burners do not light

after ODS/pilot is lit

Delayed ignition of one or both

burners

Burner backfiring during com

bustion

Yellow flame in front burner

during burner combustion

Содержание VsGF28nTF

































Результаты поиска

Содержание VsGF28nTF

Отзывы:

Похожие инструкции для VsGF28nTF

Бренды по названию

Популярные бренды

Desa VsGF28nTF, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание VsGF28nTF

Отзывы:

Похожие инструкции для VsGF28nTF

Бренды по названию

Популярные бренды