background image

www.desatech.com

119303-01A

16

PRESSURE TESTING FIREPLACE GAS 

CONNECTIONS

1.  Open equipment shutoff valve (see Figure 21, 

page 15).

2.  Open main gas valve located on or near gas 

meter for natural gas or open propane/LP 

supply tank valve.

3.  Make sure control knob of fireplace is in the 

OFF position.

4.  Check all joints from equipment shutoff valve 

to gas control valve (see Figures 22 or 23). 

Apply noncorrosive leak detection fluid to all 

joints. Bubbles forming show a leak.

5.  Correct all leaks at once.

6.  Light fireplace (see 

Operating Fireplace

, page 

17. Check all other internal joints for leaks.

7.  Turn off fireplace (see 

To Turn Off Gas to 

Appliance

,  page  18,  depending  on  your 

model).

insTallaTion

Continued

INSTALLING LOGS

 WARNING: Failure to posi

-

tion  the  parts  in  accordance 

with  these  diagrams  or  failure 

to  use  only  parts  specifically 

approved with this heater may 

result  in  property  damage  or 

personal injury. 

  CAUTION:  Do  not  remove 

the data plates attached to the 

heater base assembly. The data 

plates contain important safety 

and warranty information. 

It is very important to install these logs exactly 

as instructed. Do not modify logs. Only use logs 

supplied with heater. 

1.  Place bottom log in center of the base assem

-

bly as shown in Figure 24.

2.  Rest rear log in back corner sections of base 

assembly as shown in Figure 24. Make sure log 

is completely vertical and not leaning in toward 

burner where the flame will touch the log.

3.  Position front right log against right side of 

grate prongs (see Figure 24).

4.  Position front left log against left side of grate 

prongs (see Figure 24).

5.  Place middle right log over front right and 

bottom logs as shown in Figure 25, page 17. 

Be sure hole in middle right log seats over pin 

in bottom log.

6.  Place middle left log over front left and bot

-

tom logs as show in Figure 25. Be sure hole in 

middle left log seats over pin in front left log.

Figure 23 - Checking Gas Joints for 

Propane/LP Gas

Propane/LP 
Supply Tank

Figure 22 - Checking Gas Joints for 

Natural Gas

Gas Control Valve

Equipment Shutoff Valve

Equipment Shutoff Valve

Gas Meter

Gas Control Valve

Figure 24 - Installing Bottom Logs

Rear Log

Grate 
Prongs

Bottom 
Log

Base 
Assembly

Front Right 
Log

Front 
Left Log

Содержание VsGF28nTF

































Отзывы: